672419
15
Zoom out
Zoom in
Previous page
1/16
Next page
English Operating manual
12
Unscrew spark plug to the left
with a spark plug wrench.
Check/adjust the electrode
gap of 0.6–0.7 mm (Fig. 27).
Note
Replace a damaged, sooted
or dirty spark plug.
Screw in spark plug and tighten
to a torque of 12.3–13.5 Nm.
Do not tighten too tightly.
Cleaning the exhaust
Fig. 28
Clean the area under the exhaust
cover (1) every 25 operating hours.
To do this, the exhaust cover must
be removed.
This work may be carried out
by a specialist workshop only.
Checking/topping up the
grease in the gearbox
Fig. 29
Check the level of grease in the
gearbox every 25 operating hours.
To do this, remove the screw (1).
If required, refill with a high-quality
lithium grease.
This work may be carried out
by a specialist workshop only.
Cleaning the unit
Caution
Always keep the unit and venti-
lation slots clean and free of dirt.
Use a small brush for cleaning
the outside of the unit.
Do not use abrasive detergents.
Household cleaners which contain
aromatic oils such as pine oil
or lemon as well as solvents
such as kerosene may damage
the plastic housing and handle.
Wipe housing with a damp cloth
only.
Storage
Never store the unit with fuel
in the tank or in a location where
petrol vapours may be ignited
by a spark or naked flame.
Before storing the unit, leave
the engine to cool down.
Store the unit in a dry, closed
room to prevent unauthorised
use or damage.
Keep the unit away from children.
Long-term storage
If the unit is to be stored for a pro-
longed period, proceed as follows:
Drain all the fuel out of the tank
and pour into a container with
the same two-stroke mixture.
Do not use fuel which has been
stored for longer than 3 days.
Start the engine and leave
running until it stops.
This ensures that there is no fuel
left in the carburettor.
Leave the engine to cool down.
Take out the spark plug and pour
30 ml of a high-grade engine oil
or two-stroke oil into the cylinder.
Slowly pull the starter rope
to distribute the oil.
Reinstall the spark plug.
Note
Take out the spark plug and pour
all the oil out of the cylinder before
starting the unit after storage.
Thoroughly clean the unit and
check for loose and damaged
parts.
Repair or replace damaged parts
and tighten loose screws, nuts
and bolts.
The unit can now be stored.
Store the unit in a dry, closed
room to prevent unauthorised
use or damage.
Keep the unit away from children.
Transportation
Before transporting the unit,
leave it to cool down.
Empty the fuel tank before trans-
porting the unit.
Tank cap must be closed tightly.
Secure the unit to prevent it from
shifting during transportation.
Warranty
The warranty regulations issued
by our company or the importer
are valid in all countries.
We shall repair any faults on your
unit free of charge in accordance
with the warranty, provided the fault
was due to defective materials
or manufacturing. If claiming under
the warranty, please contact your
seller or your nearest branch.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MTD BC26 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MTD BC26 in the language / languages: English as an attachment in your email.

The manual is 2,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD BC26

MTD BC26 User Manual - German - 18 pages

MTD BC26 User Manual - Dutch - 17 pages

MTD BC26 User Manual - French - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info