Manual MTD 827 series (page 20 of 25) (English)

672474

Zoom out

Zoom in

1/25

Installation manual

Installing the cutting blade

4. Remove the cutting attachment guard.

See Removing and installing the cutting attachment

guard.

5. Place the cutting blade on the drive shaft (Fig. 14).

6. Centre the cutting blade on the drive shaft housing

(Fig. 14).

7. Ensure that the cutting blade is centred and is situated

flat against the drive shaft housing.

8. Align the shaft bush hole with the slot for the safety bar

and guide the safety bar into the shaft bush hole (Fig. 11).

9. Attach the cutting holder and nut to the drive shaft

(Fig. 14). Check that the blade has been installed

properly.

10. While holding the safety bar, tighten the nut anti-

clockwise (Fig. 15). – Tightening torque 37 Nm –

 If you do not have a torque wrench, turn the nut against

the blade holder until it is situated firmly on the shaft

bush. Check that the blade has been installed

properly and then turn the nut anti-clockwise a further

¼ to ½ turn (Fig. 15).

11. Remove the safety bar from the safety bar slot.

12. Remove the guard from the cutting blade.

Removing the cutting blade and installing the

cutting attachment (depending on model)

Removing the cutting blade

1. Attach the guard to the cutting blade.

2. Align the shaft bush hole with the slot for the safety bar

and guide the safety bar into the shaft bush hole (Fig. 11).

3. Hold the safety bar in place by gripping it together

with the shaft of the unit (Fig. 12).

4. While holding the safety bar, loosen the nut on the blade

by turning it clockwise with a screw key or socket

wrench (Fig. 16).

5. Remove the nut, blade holder and blade.

Keep the nut and blade together in a secure location for

subsequent use. Keep them out of the reach of children.

Installing the cutting attachment

6. Align the shaft bush hole with the slot for the safety bar

and guide the safety bar into the shaft bush hole (Fig. 11).

Place the blade holder on the drive shaft with the flat

surface against the drive shaft housing (Fig. 13).

Rotate the cutting attachment anti-clockwise onto

the drive shaft. Tighten firmly.

Note: The blade holder must be installed on the drive

shaft in the illustrated position, otherwise the cutting

attachment will not function properly.

7. Remove the safety bar.

8. Install the cutting attachment guard. See Removing and

installing the cutting attachment guard.

Information on oil and fuel

Recommended oil grade

Use quality oil only, API classification TC (TSC-3)

which is offered for air-cooled two-stroke engines.

Mix the oil for two-stroke engines according

to the instructions on the container, 1:40 (2.5 %).

Recommended petrol grade

Danger: Under certain conditions petrol is extremely

flammable and explosive.

– Refuel only in a well ventilated area and with the engine

switched off. Do not smoke and switch off all ignition

sources in the vicinity of the tank or at the fuel storage

depot.

– Do not overfill the petrol tank (there must be no fuel

in the inlet nozzle). After filling up the petrol tank,

ensure that the tank cap is closed and secured.

– When filling up the petrol tank, do not spill any fuel.

Spilled fuel or petrol vapours may ignite. If fuel has been

spilled, ensure that the area is dried before the engine

is restarted.

– Prevent repeated or prolonged skin contact or inhalation

of the vapours.

Always use clean, fresh lead-free petrol (maximum

30 days old).

Minimum octane number: 91 ROZ

Fill the tank with petrol

 Remove the tank cap.

 Fill fuel tank. Never overfill!

 Firmly close the petrol tank again.

 Move the unit approx. 10 m from the filling station/fuel

container before starting the engine.

See instructions on mixing oil and petrol

Age and/or incorrectly mixed fuel are the main reasons

for the unit not running properly. Use fresh, clean, lead-free

petrol only. Follow exactly the instructions for the correct

petrol/oil mixture.

Correctly mix two-stroke engine oil and lead-free petrol,

1:40 (2.5 %). Do not mix directly in the tank.

Comment retirer sur la debroussailleuse MTD827 le boîtier fil et remplacer pour la lame. Submitted on 29-10-2022 at 14:11
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of MTD 827 series in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD 827 series

MTD 827 series User Manual - German - 27 pages

MTD 827 series User Manual - Dutch - 26 pages

MTD 827 series User Manual - French - 27 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

MTD 827 series Manual

Product: