Manual MSW PROCAT 800 (page 6 of 27) (English, German, French, Italian, Spanish)

779196

Zoom out

Zoom in

1/27

EN EN

10 11

Rev. 27.02.2017 Rev. 27.02.2017

3 TECHNICAL SPECIFICATION

INSTALLATION AND TEST START-UP

1. Remove hoist from the box and check for any visible damage. Ensure there is no

damage to any of the elements.

2. Make sure all elements are in working order. Also make sure that all nuts are

tightened, then mount device on appropriate load bearing steel profile and con-

nect to the power source.

3. In order to ensure appropriate safety levels, once the electric hoist and the

traverse mechanism are switched on, check the electric power supply source.

The operator should maintain an appropriate distance from the traverse motion

mechanism, and is forbidden to perform test start-ups under that device.

SAFETY GUIDELINES:

1. The device has to be operated by qualified personnel trained within the scope of

the applicable safety rules.

2. Before using the device, the operator has to perform a test start-up without load

and check the following elements:

• Whether the switch permits the load to be lifted, lowered and arrested at any

time.

• Whether the traverse mechanism traverses freely and without obstructions.

• Whether any unusual noises occur during operation of the electric hoist.

• Whether it is possible to coil and uncoil the cable freely.

Model Procat1200 Procat800 Procat500 Procat300

Lifting capacity without pulley/with

pulley 600/990 400/800 250/500 150/300

Lift height (m)

without pulley/with pulley 12/6 12/6 12/6 12/6

Lifting speed (m/min)

without pulley/with pulley 8/4 8/4 10/5 10/5

Hoist motor power (W) 1800 1300 1020 600

Traverse motion motor power (W) 540 540 160 160

Power supply (V/Hz) 230/50 230/50 230/50 230/50

Traverse speed (m/min) 13 13 13 13

Cable diameter (mm) 5.6 5.1 4.2 3

Device weight (kg) 51 36 33 30

3. Lifting loads which exceed the lifting capacity is forbidden.

4. Do not tilt suspended loads and to not drag loads along the ground.

5. Do not use the device outside when it is raining or in unfavourable weather

conditions.

6. People and animals are forbidden to stand or pass under a suspended load (or

near it). Do not lift people or animals using this device.

7. Do not leave a suspended lead unsupervised.

8. Once suspended, balance the weight suspended on the sheave pulley.

9. The limiting switch guarantees safety and protects against overloading the hoist.

10. During operation use the break carefully, so as to prevent the load from drop-

ping. Ensure automatic elements are properly greased. Check the device every

time it is switched on.

11. Do not leave leads suspended on the hook for a long time, as this may damage

the device or cause accidents.

12. Make sure the cable is not too loose. The cable has to be coiled properly to

avoid damage. If the cable is worn out, it should be replaced.

13. Ensure every articulated part is properly greased. Every six months apply grease

to the following elements: hook, cable axis, transmission, bearing, etc.

14. Regularly, usually once a year, carry out maintenance works in order to ensure

the electric hoist remains in good working order.

15. Attention: The motor of this electric hoist works in a S3-20% 10 Min system.

Therefore a work cycle spans 10 Min., where the device is in operation for 2

minutes and then is at rest for 8 minutes. The device may not be used under a

non-stop operation mode.

FREQUENT FAULTS AND REMEDIES

Faults Possible reason Remedy

The motor does not

start after the button is

activated

• No power

• Cabling is cracked or

loose.

• The button is faulty

• The capacitor is

burned out.

• The traverse

mechanism or

traverse buttons do

not work

• Connect power

• Check and repair

cabling.

• Repair or adjust

circuit breaker

• Replace the capacitor

• Check traverse me-

chanism and replace

the traverse circuit

breaker

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of MSW PROCAT 800 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0.92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

MSW PROCAT 800 Manual

Product: