764812
15
Zoom out
Zoom in
Previous page
1/68
Next page
Spa Tub and Air Bladder Repair
Use the enclosed repair patch to repair any puncture:
1. Clean and dry the area to be repaired thoroughly
2. Apply the glue to the PVC patch and quickly attach it onto the damaged surface. (Glue is not included)
3. Smooth the surface to remove any air bubbles and allow it dry for 5-10 minutes
NOTE: Glue is not included.
1 32
pin holepin hole
15
Storage and Preparation for Future Use
1. Drain and clean the spa by following the “Drainage” and “Spa Cleaning” sections.
2. Reserve the set up instructions to deflate and disassemble the spa tub, spa
control unit and air bladder.
3. Make sure all the spa components and accessories are thoroughly clean and
dry before storage. Air-dry the spa tub in the mild sun for an hour before folding.
4. Fold the spa tub loosely and avoid any sharp corners to prevent damage or
leakage to the spa liner.
5. Prepare new additional cartridge for next time use.
6. Store the spa and accessories in a dry, temperature-controlled environment,
between 0°C and 40°C (32°F - 104°F). We recommend storing the spa with
desiccant.
7. The original packaging is recommended for storage.
8. After long-term storage, fill the spa with clean water and sanitizer, and turn on the
FILTER for at least 1 hour before use.
DISPOSAL AND ENVIRONMENTAL PROTECTION
This marking indicates that the product should not be disposed of with other household waste. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle the product responsibly to promote the sustainable reuse of
material resources. Information on disposal can be obtained from your local authorities.
To return your used device, please use the return and collection systems or contact the retailer where the product was purchased for
environmentally safe recycling.
SUN
TROUBLESHOOTING
LED READING CAUSE SOLUTION
- - -
F0
F1
Contact the MSpa Service Center
Contact the MSpa Service Center
Change the water
Contact the MSpa Service Center
Clean the parts and tubes that the water goes through
1. Add more water to the minimum line
2. Clean the parts and tubes that water goes through
3. Contact the MSpa Service Center
ERROR CODE CHART
Signal wire is loose
Communication failed
Water temperature is below 0°C (32°F) or exceeds 50°C (122°F)
Temperature sensor failure
F1 immediately shows after pressing FILTER , HEATING or UVC
F1 shows 15s after pressing FILTER, HEATING or UVC
®
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MSpa Urban - Nest at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MSpa Urban - Nest in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 3,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MSpa Urban - Nest

MSpa Urban - Nest User Manual - German - 25 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info