764785
11
Zoom out
Zoom in
Previous page
1/64
Next page
LED display
Once powered-up, press the RESET on the PRCD. The LED displays the current water temperature automatically.
NOTE: The actual water temperature may vary from the temperature displayed on the LED screen by as much as approximately 1°C.
UVC SANITIZER
Press the UVC button to turn the UVC sanitizing system on/off. When the light above this button is green, the UVC sanitizing system is
activated.
HEATING
1. Press the HEATER button to turn the heating system on/off. When the light above the heat button is red, the heating system is activated.
When the light is green, the water is at the set temperature and the heating system is at rest.
2. Pressing the UP or DOWN button will cause the LED to flash. When it is flashing you can adjust the water to the desired tempera
ture setting (from 20°C to 40°C ). The new and desired temperature setting will remain on the LED display for 3 seconds to confirm the new value.
NOTE: The default temperature is 38°C.
NOTE: If the heating system is turned on, the filtration system will automatically start.
NOTE: When the water temperature is below 1°C (33.8°F), the anti-icing system will be activated automatically to heat the water to 3°C (37.4°F).
IMPORTANT: The following conditions will lead to slow water heating
An ambient temperature lower than 10°C (50°F).
An outdoor wind speed above 3.5-5.4m/s (8-12mph).
If the air bubble function is activated when the heater is on.
If the spa cover is not properly in place when the heater is on.
FILTRATION
Press the FILTER button to turn the function on/off. The light turns to green when the function is activated.
NOTE: The filtration system will automatically start when the heating or UVC sanitizing system is activated.
NOTE: After turning off the heating system, the filtration system will automatically stop in 30 seconds.
Filter Cartridge Cleaning Reminder: When the FILTER button is flashing or displays red, the filter cartridge must be cleaned or replaced. Once
this has been done, press the Filter button for 3 seconds to reset the reminder.
BUBBLE MASSAGE
Press the BUBBLE button to turn the massage system on/off. The Bubble button displays green when activated.
IMPORTANT: Do not turn on the massage system when the cover is attached. Air can accumulate inside the spa and cause irreparable damage
and bodily harm.
NOTE: The bubbling massage function will shut down automatically after every 20 minutes of operation as a safety precaution. This can be
reactivated after 10 minutes by pressing the BUBBLE button again.
HEATING TIMER
To set the number of hours FROM NOW when the heater will activate:
1. Press the TIMER button to enter pre-setting mode. The button displays green.
2. Pressing the UP or DOWN button will cause the LED to flash. While it is flashing, you can adjust the number of hours before heater
activation (from 1 to 99 hours). The desired timer setting will remain on the LED display for 3 seconds to confirm the value.
To modify the timer setting: Press the Timer button again and use the UP or the DOWN button to adjust.
Cancel the setting: Press the TIMER button for 3 seconds.
NOTE: Activating the heating system or rebooting the spa will cancel the timer setting.
SAFETY LOCK
Press the UP and DOWN buttons at the same time for 3 seconds to lock/unlock the controller. In safety lock mode, the controller is
disabled and the spa retains all previous settings.
Celsius/Fahrenheit Toggle Button
The temperature can be displayed in either Celsius or Fahrenheit. Long press DOWN button for 3 seconds to switch.
FILTER
FILTER
HEATER
HEATER
BUBBLE
UP DOWN
TIMER
11
UVC
UVC
UP DOWN
UP DOWN
DOWN
20-40°C
1-99H
TIMER
BUBBLE
3s
UP DOWN
3s
DOWN
+
°C
°F
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MSpa Lite at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MSpa Lite in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MSpa Lite

MSpa Lite User Manual - Italian - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info