764801

MSpa Comfort - Ottoman Manual

14
Zoom out
Zoom in
Previous page
1/64
Next page
14
Storage and Preparation for Future Use
1. Drain and clean the spa by following the “Drainage” and “Spa Cleaning” sections.
2. Refer to the instructions to deflate and disassemble the spa tub, spa control unit and air
bladder (*optional).
3. Make sure all the spa components and accessories are thoroughly clean and dry before
storage. Air-dry the spa tub in mild sunlight for an hour before folding.
4. Fold the spa tub loosely and avoid any sharp corners to prevent damage or leakage to
the spa liner.
5. Prepare a new additional cartridge for next time use.
6. Store the spa and accessories in a dry, temperature-controlled storage area
(between 0°C and 40°C (32°F - 104°F).
7. The original packaging is recommended for storage.
DISPOSAL AND ENVIRONMENTAL PROTECTION
This marking indicates that the product should not be disposed of with other household waste. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle the product responsibly to promote the sustainable reuse of
material resources. Information on disposal can be obtained from your local authorities.
To return your used device, please use the return and collection systems or contact the retailer where the product was purchased for
environmentally safe recycling.
SUN
TROUBLESHOOTING
LED READING CAUSE SOLUTION
- - -
F0
F1
Contact the MSpa Service Center
Contact the MSpa Service Center
Change the water
Contact the MSpa Service Center
Clean the parts and tubes that the water goes through
1. Add more water to the minimum line
2. Clean the parts and tubes that water goes through
3. Contact the MSpa Service Center
ERROR CODE CHART
Signal wire is loose
Communication failed
Water temperature is below 0°C (32°F) or exceeds 50°C (122°F)
Temperature sensor failure
F1 immediately shows after pressing FILTER , HEATING or UV
F1 shows 15s after pressing FILTER, HEATING or UV
PROBLEM CAUSE SOLUTION
NO DISPLAY ON THE
CONTROL PANEL
SPA LEAKING
NOT HEATING
PROPERLY
Change a socket or repair the socket before use
Reset the PRCD by following the PRCD Testing section
Contact the MSpa Service Center
Contact the MSpa Service Center
Tighten the in&outlet connection
Close the drainage valve. Contact the MSpa Service Center,
if spa is still leaking
Repair the leaking hole/split with the repair kit material
Set a higher temperature
Clean or replace the filter cartridge
Add more water to the minimum line
Contact the MSpa Service Center
Refer to the "FILTER PUMP DOES NOT WORK" section
Power socket failure
PRCD is off
Press the Reset button, controller is not displayed
PRCD broken
Spa in&outlet connection not securely tight
Drainage valve is not closed completely
Water leaks from the spa pool body
Temperature set too low
Dirty filter cartridge
Water level is not at the minimum water line
Heater failure
Filter pump DOES NOT WORK
®
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MSpa Comfort - Ottoman at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MSpa Comfort - Ottoman in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 2,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info