An adequate draining system must be provided around the spa to deal with overflow water.
To reduce the risk of injury:
a) Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes. In
order to avoid the possibility of hyperthermia (heat stress) occurring, it is recommended that the average spa-
pool water temperature does not exceed 40°C (104°F).
b) Since excessive water temperatures have a high potential for causing fetal damage during the early months
of pregnancy, pregnant or possibly pregnant women should limit the spa water temperature to 38°C (100°F).
c) Before entering the spa or hot tub, the user should measure the water temperature with an accurate thermom-
eter since the tolerance of water temperature regulating devices may vary.
d) The use of alcohol, drugs or medication before or during spa use may lead to unconsciousness with the possi-
bilty of drowning.
e) The use of alcohol, drugs or medication can greatly increase the risk of fatal hyperthermia in spas.
f) The causes and symptoms of hyperthermia may be described as follows: Hyperthermia occurs when the
internal body temperature reaches a level several degrees above the normal body temperature of 37°C
(98.6°F).The symptoms of hyperthermia include an increase in the body's internal temperature, dizziness,
lethargy, drowsiness, and fainting. The effects of hyperthemia include a failure to perceive heat; a failure to
recognize the need to exit the spa; an unawareness of impending hazards; fetal damage in pregnant women; a
physical inability to exit the spa; and unconsciousness resulting in the danger of drowning.
g) Obese persons or persons with a history of heart disease, low or high blood pressure, circulatory system
problems, or diabetes should consult a physician before using a spa.
h) Persons using medication should consult a physician before using a spa since some medication may induce
drowsiness or affect the heart rate, blood pressure, or circulation.
i) Check with a doctor before use if pregnant, diabetic, in poor health, or under medical care.
People with an infectious disease should not use a spa or hot tub.
To avoid injury, exercise care when entering or exiting the spa or hot tub.
Water temperatures in excess of 40°C (104°F) may be injurious to your health.
Never use a spa or hot tub alone or allow others to use the spa alone.
Do not use a spa or hot tub immediately following strenuous exercise.
Spa heat in conjunction with alcohol, drugs, or medication can cause unconsciousness.
Exit immediately if uncomfortable, dizzy, or sleepy. Spa heat can cause hyperthermia and unconsciousness.
To prevent freezing, the spa must not be exposed to temperatures below 0°C (32°F) if there is still water in the pool.
It is helpful to place a temperature barrier mat between the spa pool and the ground. A similar mat made of foam or
any other material with a heat barrier function can also be used. Do not turn on the spa when the water is frozen.
Never pour water with a temperature higher than 40°C (104°F) into the spa directly.
Always unplug the product from the electrical outlet before removing, cleaning, servicing or making any adjustments.
Never jump or dive into a spa or any shallow body of water.
No part of the electric appliance is to be located above the bath during use.
Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge trimmers or
any other equipment.
Do not attempt to plug in or unplug the product while standing in water or when your hands are wet.
Do not use the spa if it is damaged on delivery and/or if it malfunctions in any way.
Contact the MSpa service center for further instructions.
Keep all pets away from the spa to avoid any damage.
Do not add bath oil or bath salt to the spa water.
Avoid putting your head under the water at all times.
Avoid swallowing the spa water.
The spa contains a UVC emitter. To replace or repair the UVC emitter, contact a professional operator.
8
FIRST USE AND SETUP PREPARATION
The spa can be installed indoors or outdoors in around 10 minutes by one or more persons. For household use only.
The spa must be set up on a flat, smooth and supporting surface that is able to bear the maximum load of the filled spa with the listed maximum
number of occupants. Check with a qualified contractor or structural engineer to verify the requirement.
Make sure the area is free of sharp objects under or around the spa. Uneven or unsound surface can damage the spa and void your warranty. Level
the surface before filling the spa with water.
Provide an adequate drainage system around the spa to deal with overflow water and splashes.
Make sure there is enough clearance around the spa for full access to the equipment for maintenance and/or servicing.
Consider positioning the spa to minimize noise disturbance as much as possible.
●
●
●
●
●
●
●
●
●
●
Site preparation and requirements
Humidity is a natural side effect of indoor spa installation. The room must be properly ventilated to allow moisture to escape. Install a ventilating system
to prevent excess condensation moisture in the room.
Ensure the spa can be removed from the building without destroying any part of the built structure.
Consider any local regulations on these topics.
●
●
●
Additional requirements for indoor installation
Do not set up the spa on grass or dirt, as this will increase the amount of debris entering the spa and will damage the floor.
To ensure a longer lifespan, do not leave the spa tub exposed to direct sunlight.
Always keep the manometer within the yellow section when using the spa at a temperature higher than 20°C (68°F) or when exposing it to sunlight for a
short time.
Do not install or use the spa outdoors at a temperature lower than 4°C (39°F). Do not use the spa when the water inside the circulation system, pump,
or pipework is frozen. Put a heat preservation mat (optional accessories) between the base of the spa and the ground to prevent heat loss from the
bottom of the spa and to provide better heat retention.
Additional requirements for outdoor installation
1. Plug the machine into the mains.
2. Press the RESET button on the PRCD. The indicator turns red.
3. Press the TEST button on the PRCD. The red color shown on the indicator should disappear. Otherwise the PRCD is faulty. Do not use the spa if the spa
is faulty. Contact a qualified electrician to correct the fault.
4. Press the RESET button on the PRCD again. The indicator should turn red. When it does, the spa is ready for use.
PRCD Testing
Risk of electric shock: This product is provided with a PRCD located at the end of the power cord. The PRCD must be tested before each use. Do not
use the spa if the PRCD does not function properly.
Disconnect the power cord until the fault has been identified and corrected. Contact a licensed electrician to correct the fault. There are no serviceable
parts inside the PRCD. Opening the PRCD will void the warranty.
! WARNING
Spa Control Unit Connected External Equipotential Bonding Conductors
A qualified electrician should wire the spa control unit to the household equipotential terminal using a minimum 1.5mm² solid copper conductor.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for MSpa Comfort - Bergen at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of MSpa Comfort - Bergen in the language / languages: English, German, French, Spanish as an attachment in your email.
The manual is 2,63 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
