765495
29
Zoom out
Zoom in
Previous page
1/42
Next page
EN - 2
2.2 PRELIMINARY PROCEDURES
Always wear suitable work attire, hard-wearing safety
footwear with non-slip soles and long trousers. Do
not operate the machine when barefoot or wearing
open sandals. Wear hearing protection devices.
Never wear scarves, shirts, necklaces, bracelets,



Tie your hair back if it is long.
Wear protective gloves whenever your hands are at risk.
Thoroughly inspect the entire work area and
remove anything that could be thrown by the
machine or damage the blade/rotating units
(stones, branches, iron wire, bones, etc.)
2.3 DURING OPERATION
Do not use the machine in environments at risk

liquids, gas or powder. Power tools create
sparks which may ignite the dust or fumes.
Do not expose the machine to rain or wet
environments. Water entering a power tool
will increase the risk of electric shock.

light in good visibility conditions.
Avoid working with wet grass, in the rain and when
there is a risk of a thunderstorm, especially lightening.
Pay careful attention to uneven ground
(hills, dips), slopes, hidden hazards and
obstacles that could limit visibility.
Be very careful near ravines, ditches or embankments.
The machine could overturn if a wheel slides
over the edge or if the earth gives way.
Always mow across a slope and never up and
down. Being very careful when changing direction,

wheels do not hit any obstacles (such as stones,
branches, roots, etc.) that may cause the machine
to slide sideways or make you lose control of it.
The machine must not be used on slopes over
20°, regardless of the mowing direction.
Do not incline the lawnmower during

without obstacles or high grass.
Exercise caution when pulling the lawnmower
towards you or moving backwards. Look behind
you to make sure there are no obstacles.
Never run, always walk.
Do not allow the lawnmower to pull you along.
Always keep hands and feet away from the blade,
when starting and when using the machine.
Keep away from the discharge opening.
Never operate the machine with damaged, missing
or incorrectly assembled guards (grass catcher,
side discharge guards, rear discharge guards).
Never disengage, deactivate, remove or tamper
with the safety systems/micro switches installed.
If something breaks or an accident occurs during
mowing, turn o the motor immediately and move the
machine away to prevent further damage; if an
accident occurs with injuries or third parties are
injured, carry out the rst aid measures most suitable
for the situation immediately and contact the medical
authorities for any necessary health care. Carefully
remove any debris which could cause damage or injury
to persons or animals if ignored.
2.4 MAINTENANCE, STORAGE
Ensure regular maintenance and correct storage to
maintain machine safety and high performance levels.

or damaged components. If necessary, replace the
damaged components and tighten any screws and
loose bolts or contact the authorised service centre.
Never use the machine with worn or damaged parts.
Faulty or worn-out parts must always be replaced and
never repaired. Use original replacement parts only.




with debris inside a room.
Store the machine:
Covered with a sheet where possible.
In a place where children cannot get to it.
Making sure that keys or tools used
for maintenance are removed.
Make sure that machine movements do

The noise and vibration levels shown in these
instructions are the maximum levels for use of the
machine. The use of an unbalanced cutting element,
the excessive speed of movement, or the absence of
maintenance have a signicant inuence on noise
emissions and vibrations. Consequently, it is necessary
to take preventive steps to eliminate possible damage
due to high levels of noise and stress from vibration.
Maintain the machine well, wear ear protection devices,
and take breaks while working.
2.5 BATTERY / BATTERY CHARGER
IMPORTANT The following safety instructions
are in addition to the safety requirements
provided in the specic battery and battery
charger manual delivered with this machine.
Only use battery chargers recommended by the
manufacturer to recharge batteries. An inadequate
battery charger may cause electric shock, overheating
or corrosive liquid to leak from the battery.

your power tool. The use of other batteries


inserting the battery. Inserting a battery in a

Keep all unused batteries at a distance from
paper clips, coins, keys, nails, screws or other

can cause short circuits. Short circuits between

Never use the battery charger in environments in


paper, fabric, etc. The battery charger heats

29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mountfield EL 420 Li 48L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mountfield EL 420 Li 48L in the language / languages: English, Italian as an attachment in your email.

The manual is 10,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info