481993

Moulinex Odacio Manual

16
Zoom out
Zoom in
Previous page
1/19
Next page
12
27
MINCING HEAD(depending on model)
ACCESSORIES USED
- Geared reducer assembly
(n)
and
mincer head
(o)
.
BEFORE FIRST USE
- Wash the mincer head in hot soapy
water and dry it carefully
immediately.
USE
Fitting the geared reducer onto the
food processor.
- Press the release button
(a4)
to open
the upper drive cover
(a1)
.
- Place the geared reducer onto the
lower drive
(a3)
:
- Close the upper drive cover
(a1)
.
Assembling the mincer head:
- Hold the body
(o1)
by the tube with
the largest opening at the top.Next
insert the screw
(o3)
(longest pin
first) into the body
(o1)
.
- Fit the cutter
(o4)
onto the short pin
with the cutting edges towards the
outside.
- Place the selected disc
(o5-1 or o5-2)
on the cutter
(o4)
by aligning the
hooks with the slots.
- Tighten the nut
(o6)
completely onto
the body
(o1)
in a clockwise
direction, without jamming it.
- Check the assembly. The pin must
not have any play or be able to spin.
If this is not the case, repeat the
above operations.
Fitting the mincer head onto the
appliance.
- Opposite the geared reducer (food
processor motor unit unplugged),
place the mincer head
(o)
with the
tube angled towards the right. Insert
the mincer head completely into the
geared reducer
(n)
.
- Bring the tube back to the vertical
position until it is locked in place.The
mincer head (o) will automatically
lock onto the geared reducer (n), as
soon as it is operated.
- Insert the removable tray
(o2)
onto
the tube.
- Plug in the appliance.
USE
- Prepare the entire quantity of
foodstuffs to be minced.Remove the
bones, nerves and cartilages.
- Cut the meat into pieces
(approximately 2 x 2 cm) and place
them on the tray (o2).
- Place a bowl underneath the mincer
head.
Recommended speeds
Tips
- Insert the meat into the tube piece
by piece using the food pusher
(o7)
.
- Do not push with your fingers or any
other utensil.
- Do not use your appliance for more
than 15 minutes when you are
mincing meat.
- Check that the meat is fully thawed.
Tip:
at the end of the operation, you
can process a few small pieces of
bread to clear out all of the mince.
Cleaning the mincer head
- Before any cleaning operation,
unplug your appliance.
- Release the mincer head by tilting it
to the right to remove it from the
geared reducer unit.
- To remove the mincer head, remove
the tray
(o2)
from the tube, and
unscrew the nut
(o6)
, remove the
disc
(o5)
, the cutter
(o4)
and the
screw
(o3)
.
- Handle all sharp parts with care.
- Wash all parts in hot soapy water,
Rinse them and dry them carefully.
- The disc
(o5)
and the cutter
(o4)
must remain oiled. Coat them with
oil.
- Do not allow water to enter the
geared reduced. Simply wipe it
using a soft cloth.
- Do not place the mincer head (o) in
the dishwasher, which is to say the
body (o1), the screw (o3), the cutter
(o4), the discs (o5) and the nut (o6).
SAUSAGE FUNNEL
(depending on model)
This accessory, which fits onto the
metal mincer head allows you to
Function
Electronic
Model
Two-Speed
Model
Mincing 5 2
11
11a
11b
11c
Moulf43 27/07/07 8:40 Page 28
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Moulinex Odacio at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Moulinex Odacio in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info