4888

Moulinex Atoll 200 A ER2 Manual

9
Zoom out
Zoom in
Previous page
1/50
Next page
13
- Set the temperature adjustment control (J)
to MAX. Plug in the iron. As soon as the
temperature adjustment indicator (I) goes
out, unplug the iron and place it over the sink.
Turn the steam adjustment control (C) to the
auto-clean position
and hold down the
control. Allow the tank to empty. The mix-
ture of water/steam will carry away the scale
residues contained in the soleplate.
- Then reset the steam adjustment control (C)
to position
.
- Using slow, deliberate movements, swing the
iron from left to right to give the soleplate a
good rinse and to remove the water
remaining in the soleplate. Empty the iron.
- Plug in the iron again in order to dry the
soleplate: perform this operation over a cloth
(watch out for water splashes or steam being
ejected).
- After this operation, unplug the iron once
more.
- Clean the soleplate on a cloth made of thick,
clean, damp cotton, before putting away the
iron or before using it again (iron cold).
Storage
After each use:
- Unplug the iron.
- Empty the water tank.
- Set the steam adjustment control (C) to
position
.
- Allow the iron to cool down then wind the
power cable by making a loop of about 10
cm starting from the iron.
- Store it on its heel.
What to do if your appliance
does not work
Problems Causes Solutions
The iron does not Faulty power supply Check the socket
heat up
Temperature adjust- Adjust the tempe-
ment control (J) on rature adjustment
minimum control (J)
No steam and the Steam adjustment Adjust the steam
iron is hot control (C) is in adjustment control
position
(C) to the desired
rate
The tank is empty Fill it with water
No steam and the Soleplate tempera- Set the thermostat
iron is hot ture adjustment too (J) to the steam
low for «Aqua Stop» zone, at the same
model time adjusting the
temperature accor-
ding to the type of
fabric to be ironed.
Water is dripping out Iron used for steam Wait for the adjust-
of the holes in the before the indicator ment indicator (I) to
soleplate during use light (I) has gone out go out for the first
time before going
to steam position
Steam flow rate set Reduce the flow by
too high adjusting the steam
control (C)
The spray, the pres- The tank is empty Fill it with water
sing function or the
Perfectpoint are not
working
Large reduction in Iron is starting to Perform an “auto-
the steam flow scale up clean”
Tank almost empty Fill it with water
The iron is causing The water used con- Perform an “auto-
brown marks on the tains or did contain clean” operation
laundry organic residues and change the
water. To find out
more, please refer
to the section on
“Recommended
type of water”
Water is running out Iron has been stored Set the steam
of the holes in the flat with water in the control (C) to
soleplate when it tank and store the iron
has been put away standing on its
heel.
Empty the water
from the iron.
If you have followed all these instructions
and your iron still does not work, please
contact an approved Moulinex service
centre (see list in the “Moulinex Service”
booklet).
Ironing guide
WHAT TEMPERATURE TO USE
Please refer to the labels on your laundry to
find out the composition of the fabrics or
ironing instructions.
Fers ATOLL.Eu11 17/10/00, 16:2213
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Moulinex Atoll 200 A ER2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Moulinex Atoll 200 A ER2 in the language / languages: Dutch as an attachment in your email.

The manual is 0,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info