504527
24
Zoom out
Zoom in
Previous page
1/81
Next page
DCT5100 Installation Manual
Section 3
Installation
This section provides instructions for cabling the DCT5100 and checking its operation. The
cabling diagrams assist you with the installation.
Before you begin, review the installation instructions, gather the required items, and complete
the tasks listed below:
Determine if the subscriber’s system requirements include an RF Bypass module.
Installation instructions are provided with the module if purchased separately.
Determine if you are connecting the DCT5100 to a standard TV, a composite (baseband)
monitor, or a component monitor.
Verify that you have the necessary 75-ohm coaxial cables with F-type connectors, RCA
baseband phonotype cables, or S-Video cables, as applicable.
Place the DCT5100 on a smooth, flat surface and remove any obstructions that could
interfere with the free flow of air over, under, or around it. Advise the subscriber not to
place anything on top of the unit.
Installing the DCT5100
To install the DCT5100:
1
If an add-on module is required and was not installed previously, install it now.
2
Determine if you are connecting the DCT5100 to a conventional TV, a monitor, or a
component video or high-definition television (HDTV). To install the video connection:
For a conventional TV, use a 75-ohm coaxial cable with F-type connectors.
For a monitor, use an RCA phono cable to connect the
VIDEO connector to the monitor.
For a component video or HDTV, use the component video outputs to connect to the
DCT5100.
3
Locate the cabling diagram that matches the subscriber’s configuration requirement.
4
Connect the cables as illustrated in that diagram.
5
Determine if you are connecting the DCT5100 to a data device (see “Data Devices” in this
section). For installation details, refer to instructions included with the data device being
installed.
6
Verify that the appropriate configuration information has been downloaded through the
addressable control system, after the installation of the DCT5100 is completed.
7
Perform the boot cycle, including the download for the DCT5100. For details, refer to the
boot cycle routine at the end of this section.
8
Perform the basic operational check in this section after installing the DCT5100.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Motorola DCT5100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Motorola DCT5100 in the language / languages: English as an attachment in your email.

The manual is 1,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Motorola DCT5100

Motorola DCT5100 User Manual - English - 58 pages

Motorola DCT5100 User Manual - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info