504498
47
Zoom out
Zoom in
Previous page
1/70
Next page
Diagnostics B
BB
B-
--
-5
55
5
DCT 2000 Installation Manual
Table B-3 lists the error codes:
Table B-3
Error codes
Initialization status errors
Error Code OSD Cause Remedy
E 00*
NO ERROR Indicates normal condition after initialization Not applicable
E 01*
NOT CONNECTED DCT 2000 did not receive a connect message Send a connect message
Restore out-of-band signal
E 02
PWR CYCLE Init Error Box needs a Power Cycle to
recover
E 03
DRAM DRAM error Not used at this time
E 04
DPSRAM DP-SRAM error Not used at this time
E 07
ROM ROM verification failure Power cycle box; if repetitive,
return for repair
E 08
RAM Faulty RAM, ROM, EEPROM, or POST failure
(this is a hardware failure)
Return DCT 2000 for repair
E 09
BATTERY Dead battery or memory has not been
initialized; occurs if battery fails to keep the
RAM alive during power-down; causes
DCT 2000 to be disconnected
Return DCT 2000 for repair;
requires factory initialization
message
E 10
SERIALNO Invalid serial number Not used at this time
E 11
UNIT ADDRESS Invalid unit address Return DCT 2000 for repair;
requires a unit creation message
E 12
POST POST failed Not used at this time
E 13
BOOT Sys_boot initialization failure Power cycle box; if repetitive,
return for repair
E 14
STARTUP DCT 2000 system startup failure Power cycle box; if repetitive,
return for repair
E 15
TSI INVALID TSI structure is corrupted Power cycle box; if repetitive,
return for repair
E 16
FLASH BAD NUMBER Bad flash number specified for
InitiateFlashPlatform
Error logged, ignore
E 17
BAD PLATVAL Bad platform validation step number Error logged, ignore
*E 00 and E 01 cannot b e displayed while the DCT 2000 is off. The other errors will display on
the LEDs when the DCT 2000 is off.
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Motorola DCT2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Motorola DCT2000 in the language / languages: English as an attachment in your email.

The manual is 2,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Motorola DCT2000

Motorola DCT2000 User Manual - English - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info