552864
186
Zoom out
Zoom in
Previous page
1/189
Next page
19
1
2
3
4
5
6
7
8
9
10
DISASSEMBLY/REASSEMBLY SEQUENCES AUSBAU-/MONTAGESEQUENZEN
8 FRONT WHEEL
REMOVAL
Place the motorcycle on the centre stand;
Position a support under the motorcycle to lift the front
wheel off the ground;
undo screws A that secure the brake calipers to the
fork, and remove the calipers B together with their
hoses;
undo nut C left hand side spindle pinch
loosen fork spindle pinch screws E;
withdraw spindle F, noting how spacers D are fit-
ted;
remove the front wheel from the front fork legs.
REASSEMBLY
After carrying out all necessary wheel checks, reas-
semble as follows:
Place the complete wheel between the fork legs;
Lubricate the shank and thread of the wheel spindle
with the recommended grease.
Position the spacer D, insert the spindle fully home
in the wheel hub and tighten the nut C manually;
Tighten the 2 screws E to the prescribed torque;
Secure the spindle F by tightening the nut C to the
specified torque;
Refit the brake callipers;
Check that the discs run freely inside the callipers and
then operate the brake lever repeatedly to bring the
calliper pistons to their regular position.
8 VORDERRAD
ABNAHME
Das Fahrzeug auf dem mittleren Ständer aufbocken.
Auf jeden Fall noch einen Halter unter dem Motorrad
ausrichten, der ein Abheben des Vorderrads vom Bo-
den ermöglicht.
Die Schrauben A, die die Bremssättel an den Gabel-
holmen befestigen, lösen, dann die Bremssättel B
mit noch montierten Leitungen von den Holmen neh-
men.
Die Radachsenmutter C an der linken Seite lösen.
Die Schrauben E der Befestigung der Gleitrorhe an
der Achse lockern.
Die Achse F herausziehen, dabei beachten, wie das
Distanzstück D montiert ist.
Das Vorderrad aus den Aufnahmen der Gabelholme
herausziehen.
MONTAGE
Nach Durchführung der am Rad erforderlichen Kon-
trollen die erneute Montage in folgender Weise aus-
üben:
Das komplette Rad zwischen die Gabelholme einfü-
gen.
Den Schaft und das Gewinde der Radachse mit dem
empfohlenen Fett schmieren.
Das Distanzstück ausrichten D, dann die Radachse
an der Radnabe auf Anschlag bringen und die Mutter
C mit der Hand anziehen.
Die 2 Schrauben E auf das vorgeschriebene Anzugs-
moment bringen.
Die Achse F mit der Mutter C auf das vorgeschrie-
bene Anzugsmoment bringen.
Die Bremssättel montieren.
Kontrollieren, ob die Bremsscheiben frei zwischen den
Bremssätteln laufen, dann den Bremshebel mehrmals
betätigen um die Bremssattelkolben in ihre normale
Position zu bringen.
186


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Moto Guzzi 1100 ES Quota at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Moto Guzzi 1100 ES Quota in the language / languages: English, German, Italian as an attachment in your email.

The manual is 7,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info