Manual Morso 7990 (page 35 of 40) (English, Danish)

744316

Zoom out

Zoom in

1/40

NO SV

Internal cast-iron parts and/or wearing parts

The baes and other components that come in direct contact with the re and glowing

fuel are all wearing parts. As a result, they will be particularly susceptible to burn-through.

When used correctly, these parts will last for many years, but overly vigorous use will natu-

rally accelerate the burn-through. Such parts are all easily replaced.

If the baes are damaged and are not replaced in time, the top plate will be exposed to

such high temperatures that it may be damaged as well.

Please note that no unauthorised alterations of the design may be undertaken, and

that any parts that are replaced must be replaced with original Morsø parts.

Gaskets

The gaskets in the door will wear out over time, and should be replaced as required in or-

der to prevent runaway combustion. Use the original Morsø gasket kit.

NOTE: Normal wearing parts are not covered by Morsø’s extended warranty.

A selection of maintenance products (spare parts, glass cleaner, paint, gasket kit, etc.)

is available from your Morsø dealer.

3.3 Cleaning the stove

A layer of ash and soot will form as a result of the draught in the chimney and after sweep-

ing, particularly on the top of the casted smoke hood. This ash will have an insulating ef-

fect, which may speed up the burn-through of the bae.

During normal cleaning, the bae and the smoke hood can be removed from the stove.

Once these parts have been taken out, you can access the ue chamber above the bae

and clean it.

Clean the bae and smoke hood before reassembling them, and make sure that they are

correctly assembled. Nowadays the chimney sweep must remove the soot in the stove, in ad-

dition to sweeping the chimney and cleaning the ue pipe. The number of annual sweepings/

cleanings of the stove should be determined in consultation with your chimney sweep.

Ash

As noted above, there should be a couple of centimetres of linsulating ash in the bottom of the

combustion chamber in order to achieve a high combustion temperature. If the layer of ash is

too thick, it can be brushed down into the ash pan. Empty the ash pan before it gets comple-

tely full, so that the ash does not insulate around the grate, and thereby speed up the burn-

through. In most cases, the ash will need to be taken away by the waste disposal company. Be-

cause embers may be concealed in the ash pan for several days, it may be necessary to store

the ash in a container made of non-ammable material before pouring it into a rubbish bag.

Reasons for overly rapid wear of internal parts

- Stove red too vigorously

Use of very dry wood (wood from old furniture)

- Too much soot on top of the baes (please see the section on Cleaning)

- Too much ash in the ash pan (please see the section on Ash)

Note: Should be handed in to a recycling station as ceramic glass.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Morso 7990 in the language / languages: English, Danish as an attachment in your email.

The manual is 2,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Morso 7990

Morso 7990 User Manual - German - 20 pages

Morso 7990 Usermanual and installation guide - Dutch, French - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Morso 7990 Manual

Product: