Manual Morso 6843 (page 13 of 21) (English, Danish)

744342

Zoom out

Zoom in

1/21

DK ENG

1.6 Connecting the ue pipe

Lift the upper cast iron top plate o the stove.

Note: The included round cast iron cover plate must be mounted on the upper cast iron top

plate if the stove is being installed with the ue pipe to the rear.

Mounting the ue collar pointing upwards

From the factory, the stove is prepared for installation with the included ue collar (1) point-

ing upwards with included ball stop and screws. The ball stop, which prevents the chimney

sweep from damaging the stove’s bae plates while sweeping, is the 145 mm long rod that

is provided.

Mounting the ue collar to the rear

If the stove is being installed with the

ue pipe to the rear, the round plate

fixed with two screws on the back

of the stove is dismounted. The iron

piece on the inside convection back

panel is knocked out with light, rm

taps with a hammer next to the small

”bridges” holding the piece.

The cast iron cover is removed from

the back panel and mounted on the

top plate. The ue collar is centred and

screwed onto the back of the stove

with the clamps and screws provided.

The ball stop is not used when install-

ing the ue collar to the rear.

The location of the baes

The baes (2) and (3), which are made

from vermiculite, are mounted at the

factory.

Make sure that the baes are correct-

ly assembled before lighting the stove

(please see the sketch).

1.7 Connecting to a brick chimney

Brick a ue bushing securely into the wall, and insert the ue pipe into it. The pipe must not

extend into the actual chimney opening, but only to the inside of the chimney aperture. The

joints between the stove/pipe and pipe/wall bushing must be sealed with the glass tape pro-

vided. It is not normally necessary to seal between any pipe joints.

If the ue pipe transitions from horizontal to vertical, it is a good idea to install it with a gentle

bend so as to avoid any loss of draught.

The ue pipe must be dimensioned in accordance with national and local regulations. Morsø

recommends, however, that ue pipes be made of 2 mm sheet steel as this will extend the

service life.

1.8 Connecting to a steel chimney

If your installation involves taking the chimney straight up and through the ceiling, you must

comply with National, Local Building Regulations or ue manufacturers instructions concern-

ing clearances to combustible materials such as walls, oor joists and ceilings. The joint be-

tween the stove ue collar and the stovepipe must also be sealed using the glass bre rope

provided. It is important that the insulated ue system is properly supported both at ceiling

level and at roof level.

THE STOVE MUST NOT BEAR THE WEIGHT OF THE CHIMNEY SYSTEM (See chimney man-

ufacturer’s instructions). Excessive weight on the stove will inhibit expansion and could lead

to damage of the stove top. Damage caused to the stove in this way would not be covered by

the manufacturers guarantee.

If a chimney re should occur as a result of incorrect operation of the stove or prolonged

use of wet fuel, close the vents completely and contact the re brigade.

Be aware of the following:

Cleaning procedure: Discuss this with chimney sweep or qualied installer prior

to or during the stove installation.

Chimney draft: If the chimney draft is naturally poor it is better to install the ue from

the top of the stove so as to minimise any internal resistance of the ue gases.

Avoid having any more than 2 bends in the ue system and limit the length of the

oset between bends.

Fresh air supply

A wood-burning stove requires air for combustion. As a result, ring a wood-burn-

ing stove will help create a healthy climate in your house. If the house is very tightly

sealed, and particularly if there is a cooker hood or ventilation system in the house, it

may be necessary to install an air grate in the room in which the wood-burning stove

is installed. Otherwise there may not be enough draught in the chimney, which may

result in the stove not being able to burn properly, and smoke may come out of the

stove when the re door is opened.

If it is necessary to install air grates, they must be positioned so that they cannot

be obstructed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Morso 6843 in the language / languages: English, Danish as an attachment in your email.

The manual is 0,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Morso 6843

Morso 6843 Usermanual and installation guide - German - 20 pages

Morso 6843 Usermanual and installation guide - Dutch, French - 40 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Morso 6843 Manual

Product: