Manual Morso 6800 series (page 16 of 21) (English, Danish)

744348

Zoom out

Zoom in

1/21

DK ENG

We would strongly recommend that you do not leave your stove alit at night. It

harms the environment and constitutes very poor use of the wood as the gases

in the wood do not ignite at the low temperature, but settle as soot (unburned

gases) in the chimney and stove. Extreme conditions, such as poor draught in the

chimney, large quantities of wood or wet wood, may in the worst-case scenario

cause an explosive ignition.

When ring in the summer period, when there is minimal need for heat, the combustion

will be poor. The stove provides too much heat so the combustion should be reduced.

But always remember to make sure that there are lasting ames until the wood be-

comes charcoal. If you want a weaker re, stoke up using less wood.

If you re the stove using wet wood, a lot of the fuel’s thermal energy will be spent

forcing the water out of the wood, without releasing any heat to the stove. This

incomplete combustion results in a layer of soot being left in the stove, pipe and

chimney.

Comparison between ring with wood and oil:

Type of wood (moisture content 20%) No. of cubic metres per 1000 litre oil

Oak

Beech

Ash

Sycamore

Birch

Elm

Common spruce

Silver r

7.0

7.2

7.5

8.0

8.9

10.4

10.9

Refuelling on to a low re bed

If there is insucient burning material in the rebed to light a new fuel charge, excessive

smoke emission can occur. Refuelling must be carried out onto a sucient quantity of

glowing embers and ash that the new fuel charge will ignite in a reasonable period. If there

are too few embers in the re bed, add suitable kindling to prevent excessive smoke

Fuel overloading

The maximum amount of fuel specied in this manual should not be exceeded, overloa-

ding can cause excess smoke.

Operation with door left open

Operation with the door open can cause excess smoke. The appliance must not be ope-

rated with the appliance door left open except as directed in the instructions.

Dampers left open

Operation with the air controls or appliance dampers open can cause excess smoke. The

appliance must not be operated with air controls, appliance dampers or door left open

except as directed in the instructions

3.0 Routine stove maintenance

3.1 External maintenance

The cast surface of the stove is painted with heat-resistant Senotherm paint. It is best main-

tained by simply vacuuming it with a soft brush attachment or wiping it down with a dry,

dust-free cloth.

If the stove is used too vigorously, the painted surface may assume a greyish tinge over time,

but the stove can easily be freshened up with Morsø spray paint, which is available from your

local retailer.

Morsø stoves are painted using a Morsø Original Black (previously called Morsø dark grey)

or Morsø grey. The paint can be bought in a spray or a can.

3.2 Internal maintenance

Glass window

If the stove is used correctly, very little or no soot will be deposited on the ceramic glass window.

If soot does form on the glass as the stove is being lit, it will burn away once normal combustion

begins in the stove. If the glass window becomes thoroughly covered in soot due to incorrect op-

eration, the soot can be easily removed using a cleaning agent such as Morsø Glass Cleaner. The

glass must be cold when you clean it. Avoid stoking the stove with pieces of wood that are so long

that they press against the glass window when the door is closed.

Ceramic glass replacement

Ceramic glass cannot be recycled because it has a higher melting point that ordinary glass.

If ceramic glass is mixed with ordinary glass, the raw material is spoiled, and the reclaiming

process may be halted. Take care that the ovenproof glass does not end up among ordinary

recycled waste. That will be a great benet to the environment.

Note: Should be handed in to a recycling station as ceramic glass.

Internal cast-iron parts and/or wearing parts

The baes and other components that come in direct contact with the re and glowing fuel

are all wearing parts. As a result, they will be particularly susceptible to burn-through. When

used correctly, these parts will last for many years, but overly vigorous use will naturally ac-

celerate the burn-through. Such parts are all easily replaced. If the baes are damaged and

are not replaced in time, the top plate will be exposed to such high temperatures that it may

be damaged as well.

Please note that no unauthorised alterations of the design may be undertaken, and that

any parts that are replaced must be replaced with original Morsø parts.

Reasons for sooty glass window:

- The fuel is too wet.

- The pieces of fuel are to big/uncut wood.

- The combustion temperature is too low.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Morso 6800 series in the language / languages: English, Danish as an attachment in your email.

The manual is 0,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Morso 6800 series

Morso 6800 series Usermanual and installation guide - German - 20 pages

Morso 6800 series Usermanual and installation guide - Dutch, French - 40 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Morso 6800 series Manual

Product: