Manual Morso 6143 (page 15 of 21) (English, Danish)

744336

Zoom out

Zoom in

1/21

DK ENG

2.0 Firing/using the stove

Your stove is constructed with air inlets in two places.

Pre-heated, fast-moving combustion air is added to the re above the glass window, and is

regulated using the handle above the door. The combustion air is let in when the handle is

pushed to the right, and shut o when the handle is pushed to the left.

Another air inlet provides constant, pre-heated air supply which cannot be adjusted, and which

comes into the combustion chamber just above the re. This helps burn o the last few gasses

emitted by the wood while it is being heated.

The stove’s rated heat output is 5,0 kW.

Your new Morsø stove is EN-tested for ring with wood, and is suitable for intermittent use.

NB!

Wood is a material that contains a great deal of gas (approx. 75%). The gases are released

when the wood is lit and heated. For this reason, it is important that these gases are ig-

nited quickly after stoking. If the wood just lies smouldering, especially after re-stoking,

a lot of smoke is created which, in the worst case, may cause an explosive ignition of the

gases, resulting in damage to the stove.

In order to ignite the gases that are released from the wood, and to keep clear, lasting

ames during the combustion process, it is important to let in the required quantity of

oxygen (air supply) at all times. The setting of the air supply, the method of ignition and

the lighting intervals depend on the draught in the chimney, the wind and weather, the

amount of heat required, the fuel, etc. This means that it may take some time before

you get to know the correct functioning of the stove under any given circumstances.

Although you can re your Morsø stove with almost all kinds of wood, you should

not re with wet wood, or unseasoned wood. Wood ought to be stored under a roof

for at least 1 year, and preferably 2 years, with free access to wind. Wood should be

chopped as soon as possible after felling if it is to dry quickly. The wood can be used

once the moisture is less than 20%. During the test, all stoves are tested with wood

with a moisture content of (16 ± 4)%.

Never use driftwood as it usually has a high salt content, which damages both

the stove and the chimney. Impregnated and painted wood and chipboard emit

poisonous smoke and fumes so they should not be used as fuel either

Please note that liquid fuel may not be used in the stove.

Pieces of wood with a diameter exceeding 10 cm should always be chopped. The pieces

of wood should be short enough to be able to lie at over the layers of embers, with air

at both ends. The maximum length of fuel in the stove is 30 cm. The maximum quantity

of fuel is approx. 2 kg/hour (max. 2 pieces of wood each time you re-stoke).

The rst few times you light the stove, the re should be moderate so that the heat-

resistant paint can harden before ring more vigorously. During the hardening phase,

the paint may develop obnoxious smoke and smell the rst time it is lit, which is very

normal. Make sure that the room is well ventilated during this period.

When heating up or cooling down, the material is exposed to major temperature

dierences that may cause the stove to give o creaking sounds.

2.1 Lighting instructions and fuelling intervals

A lot of air is needed when lighting the stove. If you are starting with a cold stove, the door should

be left ajar for the rst few minutes and the combustion air supply opened to maximum.

In order to build up an insulating layer of ash in the bottom of the stove, you should burn 1-1.5

kg of dry kindling when you light the stove the rst time.

Always keep approx. 1 cm ash in the bottom of the combustion chamber.

1. We recommend using the “top-down” method to light your

wood-burning stove. It is the most environmentally-friendly

method of lighting. Use two relighters and approx. 1.5 kg of dry

kindling sticks to quickly create a glowing layer of wood. Place

the relighters directly under the top layer of kindling sticks.

2. Open the air supply as much as possible. This is done

using the handle above the door.

3. After the paper/solid alcohol tablets have caught re,

leave the re door ajar about 5-10 cm so that the chimney

draws well.

4. When you can see that the chimney is hot enough to draw

(after 5-10 minutes), close the door. If all the necessary condi-

tions are met, a thick layer of embers will have been formed in

the combustion chamber after another 15-20 minutes.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Morso 6143 in the language / languages: English, Danish as an attachment in your email.

The manual is 0,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Morso 6143

Morso 6143 Usermanual and installation guide - German - 20 pages

Morso 6143 Usermanual and installation guide - Dutch, French - 36 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Morso 6143 Manual

Product: