Manual Morso 4441 (page 13 of 19) (English, Danish)

744508

Zoom out

Zoom in

1/19

DK ENG

1.6 Connecting the ue pipe

The ue collar can be rotated and be used for ø150 (inside and outside the ue collar) and

ø120 connections.

Mounting the ue collar pointing upwards

From the factory, the stove is prepared for installation with a top exit ue collar (1). Take the

bae plates out of the stove to facilitate the installation. The enclosed cast-iron ue collar

is fastened to the top of the stove with the included screws. The ball stop, which prevents

the chimney sweep from damaging the stove’s bae plates while sweeping, is the 160 mm

long rod that is provided in the stove. The ue collar stop bar is tted when installing the

chimney.

Mounting the ue collar to the rear

Take the bae plates out of the stove to facilitate the installation.

Remove the knock out cover from the rear heat shield with easy rm taps of a hammer next

to the small conneting “bridges”. Now remove the cover from the rear convector plate using

the same method. Next, the round cover is unscrewed from the back panel of the stove and

reinstalled in the hole in the top panel. The enclosed cast-iron ue collar is fastened to the

back of the stove with the included screws.

The ball stop is not used when installing with the ue collar to the rear.

Finally, the enclosed cover plate is put in place in the top panel to cover the hole.

The location of the baes

The baes (2) and (3), which are made from vermiculite, are mounted on delivery.

Make sure that the baes are correctly assembled before lighting the stove (please see

the sketch).

Fresh air connection, if required

The stove is factory prepared for installation of

an optional extra adaptor (4) for a fresh air

connection underneath or backwards the stove. .

SECTION L-L

SCALE 1 : 2

Zone: Rev.:

Description

Date

Sign.:

Revisions

Title:

Drawing no.:

1:5

Morsø 4400

18408,1

Date of print: 22-05-2017

Itemno.:

This drawing is Morsø Jernstøberi A/S' property and must not be sold, lended or copied without any written authorization from the company.

Material:

Weight kg.:

Model no.

Drawingtype:

Location of file:

Scale:

Format:

Released:

Construction:

1.7 Connecting to a brick chimney

Brick a ue bushing securely into the wall, and insert the ue pipe into it. The pipe must not

extend into the actual chimney opening, but only to the inside of the chimney aperture. The

joints between the stove/pipe and pipe/wall bushing must be sealed with glass tape. It is not

normally necessary to seal between any pipe joints.

If the ue pipe transitions from horizontal to vertical, it is a good idea to install it with a gentle

bend so as to avoid any loss of draught.

The ue pipe must be dimensioned in accordance with national and local regulations. Morsø

recommends, however, that ue pipes be made of 2 mm sheet steel as this will extend the

service life.

1.8 Connecting to a steel chimney

If your installation involves taking the chimney straight up and through the ceiling, you must

comply with National, Local Building Regulations or ue manufacturers instructions concern-

ing clearances to combustible materials such as walls, oor joists and ceilings. The joint be-

tween the stove ue collar and the stovepipe must also be sealed using the glass bre rope

provided. It is important that the insulated ue system is properly supported both at ceiling

level and at roof level.

THE STOVE MUST NOT BEAR THE WEIGHT OF THE CHIMNEY SYSTEM (See chimney man-

ufacturer’s instructions). Excessive weight on the stove will inhibit expansion and could lead

to damage of the stove top. Damage caused to the stove in this way would not be covered by

the manufacturers guarantee.

If a chimney re should occur as a result of incorrect operation of the stove or prolonged

use of wet fuel, close the vents completely and contact the re brigade.

Be aware of the following:

Discuss the cleaning options with your chimney sweep.

If there is insucient draught in the chimney, it may be a good idea to install the ue

pipe straight up so as to minimise smoke migration in the actual combustion chamber.

Avoid having more bends than necessary, and limit the length of the ue pipe so

as not to reduce the draught.

Fresh air supply

A wood-burning stove requires air for combustion. As a result, ring a wood-burn-

ing stove will help create a healthy climate in your house. If the house is very tightly

sealed, and particularly if there is a cooker hood or ventilation system in the house, it

may be necessary to install an air grate in the room in which the wood-burning stove

is installed. Otherwise there may not be enough draught in the chimney, which may

result in the stove not being able to burn properly, and smoke may come out of the

stove when the re door is opened.

If it is necessary to install air grates, they must be positioned so that they cannot

be obstructed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Morso 4441 in the language / languages: English, Danish as an attachment in your email.

The manual is 0,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Morso 4441 Manual

Product: