Manual Morso 4412 (page 12 of 19) (English, Danish)

744506

Zoom out

Zoom in

1/19

DK ENG

1.0 Installing your Morsø stove

1.1 Unpacking the stove

When shipped, the basic stove is ready for mounting legs or a base. The Morsø 4400

Series stoves weigh from 85 to 98 kg (188 to 216 pounds). In order to avoid damages, it is

recommended that two persons unpack and install the stove.

The stove can be delivered with dierent leg options. If the stove is placed on a combustible

oor the minimum leg length must be 200 mm.

1.2 Installing the stove

When shipped, the stove is prepared for installation with a top ue exit. The cast-iron ue collar

and the ball stop, which stops the chimney sweeper’s ball when sweeping, are included with the

stove and are installed when the chimney pipe is installed.

National and local regulations regarding the installation of wood-burning stoves must be observed,

as must local regulations regarding chimney connections and chimney installation. You may want to

ask your chimney sweep for advice. However, you, your technical adviser or workman are responsi-

ble for complying with the applicable national and local regulations.

1.3 Chimney sweep

As stated, it may be wise to consult your local chimney sweep before installing the stove. In

any event, the chimney sweep must be notied once the wood-burning stove has been in-

stalled. The chimney sweep will inspect the installation and schedule sweeping intervals with

you. If your chimney has not been used for some time, it should be inspected for cracks, bird

nests, etc., before it is used.

1.4 Location of the stove/distance requirements

Distance requirements apply only if the stove is placed near ammable materials. Your new

stove can be positioned as specied on the certicate of approval on the back of the stove

if the walls are made of ammable material.

Minimum distances from ammable material:

Type of stove Behind the stove (A)

To the sides of the

stove (B)

To furniture

Morsø 4400

uninsulated ue

pipe

300 mm 450 mm 1100 mm

Morsø S4400

insulated ue pipe

200 mm 450 mm 1100 mm

Min. afstand til brandbar væg for Morsø S11

Revisions

Rev.

Sign.:

Title:

Drawing no.:

Dim. without indication of margin acc. to DS/ISO 2768-1 m

1:10

Afstand til hjørnevæg

Distance to Corner wall

Morsø S11-40

RSV

Dimension Skecth

Date of print: 10-08-2011

U:\udv\Tegninger\Diverse\Afstand til brandbare vægge\Afstand til hjørnevæg.SLDASM

S-11-020 a

Itemno.:

This drawing is Morsø Jernstøberi A/S' property and must not be sold, lended or copied without any written authorization from the company.

Material:

Weight:

Model no.

Drawingtype:

Location of file:

Scale:

Format:

Released:

Construction:

Date:

Side 1 of 4

2011.07.11

45°

Min. afstand til brandbar væg for Morsø S11-40

Revisions

Rev.

Sign.:

Title:

Drawing no.:

Dim. without indication of margin acc. to DS/ISO 2768-1 m

1:10

Afstand til hjørnevæg

Distance to Corner wall

Morsø S11-40

RSV

2011.07.11

Dimension Skecth

Date of print: 10-08-2011

U:\udv\Tegninger\Diverse\Afstand til brandbare vægge\Afstand til hjørnevæg.SLDASM

S-11-020 a

Itemno.:

This drawing is Morsø Jernstøberi A/S' property and must not be sold, lended or copied without any written authorization from the company.

Material:

Weight:

Model no.

Drawingtype:

Location of file:

Scale:

Format:

Released:

Construction:

Date:

Side 2 of 4

We recommend that the stove be installed at least 10-15 cm from masonry in order to allow

heat to circulate and to facilitate the cleaning of the inside and outside of the stove. A layer

of wallpaper on a brick wall is normally regarded as non-ammable material.

The oor

If the stove is installed on a ammable oor, national and local regulations must be observed

with regard to the size of the non-ammable underlying surface that must cover the oor be-

neath the stove.

The underlying surface must naturally be able to bear the weight of the stove and, if ap-

plicable, the steel chimney.

Distance to furniture

We recommend that the stove be installed 1100 mm from furniture, but consideration should

also be given to whether furniture, etc., will dry out as a result of its proximity to the stove.

The distance to ammable material in front of the stove is 1100 mm.

A wood-burning stove gets hot when it is red. Caution must therefore be observed, par-

ticularly with regard to children touching the stove.

1.5 The chimney

If local regulations permit, the stove may be connected to a chimney already serving anoth-

er replace (such as an oil-burning stove or another wood-burning stove). Attention should

be paid to any requirements concerning the location of ue pipes if two or more replaces

are connected to the same chimney.

The wood-burning stove must never be connected to a chimney to which a gas-burning stove

is already connected. An ecient, modern stove places great demands on the chimney, so have

a chimney sweep check the condition of your chimney.

The aperture of the chimney must comply with national and local regulations. In general,

the aperture area should measure at least 175 cm2 (150 mm diameter) for wood-burning

stoves. Exceptions to this are: Smoke Exempt Morsø stoves tted with a 125mm diameter

ue collar. These can be connected to a chimney system or liner with a minimal cross sec-

tional area of 123 cm² (125mm diameter)

An overly large chimney aperture will mean that too much energy will be required to heat

the chimney suciently to achieve an acceptable draught. If you have a brick chimney with

a large aperture, we recommend that you install an insulating chimney liner of the proper

diameter. This will increase the draught, and improve the fuel economy.

There are no requirements with respect to specic chimney heights, but a chimney must be

tall enough to provide a good draught, and to ensure that the smoke does not cause any prob-

lems. As a general rule, there will be a satisfactory draught if the chimney extends 4 metres

above the stove and at least 80 cm above the spine of the roof. If the chimney is located along

the side of the house, the top of the chimney should never be lower than the spine of the roof

or the highest point on the roof. Please note that there are often national and local regula-

tions regulating the location of chimneys in houses with thatched roofs. Please see section

1.9 Draught.

The chimney and the ue pipe must be tted with cleaning doors, which must be at least

the same size as the chimney’s aperture area.

The chimney must be accessible for external inspection, and it must be possible to access

the cleaning doors and the chimney if it is to be cleaned from the top (e.g. steel chimneys).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Morso 4412 in the language / languages: English, Danish as an attachment in your email.

The manual is 0,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Morso 4412 Manual

Product: