744323

Morso 3112 Manual

16
Zoom out
Zoom in
Previous page
1/19
Next page
30
31
DK ENG
3.0 Routine stove maintenance
3.1 External maintenance
The surface of the stove is painted with heat-resistant Senotherm paint. If the stove is used
too vigorously, the painted surface may take-on a greyish tinge. It is easily maintained by sim-
ply vacuuming the surface with a soft brush attachment and applying two light layers of paint.
Morsø stoves are painted using a Morsø Original Black (previously called Morsø dark grey)
or Morsø grey. The paint can be bought in a spray or a can.
3.2 Internal maintenance
Ceramic glass
If the stove is used and installed onto a ue with the correct draft, very little or no deposits
should appear on the ceramic glass. It is usual for soot deposits to appear during long slum-
bering res however, once the re has been re-established to a burn brightly, these deposits
should burn o.
If the glass window becomes thoroughly covered in soot due to faulty operation or poor
draft, the soot can be easily removed using, e.g. Morsø Glass Cleaner, but please ensure that
the glass is cold before cleaning. Avoid fuelling the stove with wood that is so long that it
presses against the glass when the door is closed.
Ceramic glass replacement
Ceramic glass cannot be recycled because it has a higher melting point that ordinary glass.
If ceramic glass is mixed with ordinary glass, the raw material is spoiled, and the reclaiming
process may be halted. Take care that the ovenproof glass does not end up among ordinary
recycled waste. That will be a great benet to the environment.
Note: Should be handed in to a recycling station as ceramic glass.
Internal cast-iron parts and/or wear components
The shaking grate, bae plate and other internal components that are in direct contact with
the re are all constituted as ‘wear’ components or consumables, as, they are exposed to
the most wear. When used properly, these parts will last for many years, but overly vigorous
use will naturally shorten the lifespan. The aforementioned parts are all easily replaceable.
If the bae plate is damaged or warped and is not replaced in time, the top plate could be-
come subject to excessively high temperatures, which may lead to damage here also.
Note: that no unauthorised alterations to the stove design should be undertaken, and
always ensure that any replacement parts purchased are Morsø original parts.
Reasons for sooty glass window:
- The fuel is too wet.
- The pieces of fuel are to big/uncut wood.
- The combustion temperature is too low.
- Too much air coming through the bottom grate.
- Poor chimney draft.
Reasons for overly rapid wear of internal parts
- Stove red too vigorously.
- Too much air coming through the bottom grate.
- Use of very dry wood (wood from old furniture).
- Too much soot on top of the baes (please see the section on Cleaning).
- Too much ash in the ash pan (please see the section on Ash).
Gaskets
The rope gaskets in the door will need regular inspection in order to ensure and maintain
full control of your stove’s burning rate; over time the rope gaskets will harden and will be-
come less airtight; at this point you will need to remove and replace with new. Use only the
genuine Morsø gasket kit, which comes with detailed replacement instructions.
NOTE: Normal wear components (inner parts) are not covered by Morsø’s 10-year
guarantee.
Maintenance products (Spare Parts, Glass Cleaner, Paint, Gasket Kit, etc) are all available from
your authorised Morsø dealer.
3.3 Cleaning the stove
During normal use and sweeping of your stove and chimney, a layer of ash, soot or debris
can form, particularly on the top of the bae plate or inner reback. Any deposits allowed
to build-up over time will have an insulating eect on these parts, thus restricting expan-
sion; this will ultimately result in a shorter lifespan. The chrome-iron bae plate and inner
reback/bricks can easily be removed from the stove and should be regularly checked for
debris and cleaned. You must ensure that your chimney sweep removes all soot and debris
from the stove after the sweeping process.
Your chimney should be swept at least once a year; however a regular inspection of your stove-
pipe and chimney will determine whether a more frequent approach should be adopted.
Ash
In order to achieve the highest combustion temperature possible when burning solely wood,
it is important that a 1cm deep bed of ash is established on top of the grate area. Excess ash
should be removed by simply agitating the grate by moving the riddling rod on the outside
of the stove; surplus ash will fall into the ash pan below the grate where it can be easily and
safely removed.
Be sure to empty the ash pan before it gets completely full; if the ash level reaches the under-
side of the grate, air ow through the grate will be restricted and will lead to over-heating and
premature wear of the grate parts.
When emptying the ash pan always dump the waste ash into a metal container (dustbin)
where it can fully cool before being taken away by your refuse collector. Ash from a wood-
burning stove does not benet your garden as fertiliser.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Morso 3112 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Morso 3112 in the language / languages: English, Danish as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Morso 3112

Morso 3112 Usermanual and installation guide - German - 11 pages

Morso 3112 Usermanual and installation guide - Dutch, French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info