Manual Morco GB30 SII (page 12 of 36) (English)

646333

Zoom out

Zoom in

1/36

SECTION 4 - gENEral INSTallaTION rEquIrEmENTS

4.1 RECOMMENDATIONS

Current Gas Safety (Installation and Use) Regulation or Rules in

Force.

Theboilerissuitableonlyforinstallationinthespeciedcountries

and should be installed in accordance with the rules in force.

In GB, the installation must be carried out by a Gas Safe

RegisteredEngineer,orinothercountriesaqualiedand

competent Gas Installer. It must be carried out in accordance with

the relevant requirement of the:

• GasSafety(InstallationandUse)Regulations

• AppropriateNationalStandards

• TheWaterFittingsRegulations

• CurrentIEEWiringRegulations

• Health&SafetyDocumentNol.635

• TheElectricityatworkRegulations1989.

• BS5482Part1CodeofPracticeforDomesticbutaneand

propane gas burning installation in permanent dwellings,

residential park homes and commercial premises.

• BSEN1949:2011SpecicationfortheinstallationofLPG

Systems for habitation purposes in leisure accommodation

vehicles and other road vehicles.

IMPORTANT

The manufacturer’s notes MUST NOT be taken, in any way as

overriding statutory obligations.

4.2 BOILER LOCATION

Theboilermustbeinstalledonaatandverticalwall,capableof

adequately supporting the weight of the boiler and any ancillary

equipment.

Theboilermaybettedonacombustiblewallandinsulation

between the wall and the boiler is not necessary unless required

by National Standards.

For Electrical Safety reasons there must be no access available

from the rear of the boiler.

Theboilermustnotbettedoutside.

BATHROOM INSTALLATIONS

This appliance is rated IP20.

The boiler may be installed in any room or internal space, although

particular attention is drawn to the requirements of the current

IEE (BS.7671) Wiring Regulations and the electrical provisions

of the building regulations applicable in Scotland, with respect to

the installation of the boiler in a room or internal space containing

a bath or shower. For IE reference should be made to the current

ETCI rules for electrical installations and I.S. 813:2002.

If the appliance is to be installed in a room containing a bath or

shower then, providing water jets are not going to be used for

cleaning purposes (as in communal baths/showers), the appliance

must be installed beyond Zone 2, as detailed in BS.7671.

0.6m

Zone 0

Recessed

window

Zone 2

Ceiling

3G8913a

2.25m

Zone 1

COMPARTMENT INSTALLATIONS

A compartment used to enclose the boiler should be designed

and constructed specially for this purpose.

An existing cupboard or compartment may be used, provided

thatitismodiedforthepurpose.

• ThepositionselectedforinstallationMUSTallowadequate

space for servicing in front of the boiler.

4.3 FLUE TERMINAL POSITION

Pluming will occur at the terminal so avoid locations where this

will cause a nuisance.

The boiler MUST be installed so that the terminal is exposed to

external air.

It is important that the positions of the terminal allows the free

passage of air accross it at all times.

Minimum acceptable spacing from the terminal to obstructions

andventilationpumparespeciedinthetablebelow.

ForCaravanHolidayHomes;iftheheightoftheueterminal

from any ground, decking or steps is under 1.5m then a suitable

terminalguardshouldbetted.

For Residential Park Homes, please refer to BS 5440 Part 1.

Terminal Guards are available from boiler suppliers.

TFC Flue Guard - Model K6 Round Plastic Coated.

www.tfc-group.co.uk

* Only one reduction down to 25mm is allowable per installation

otherwise BS5440-1 2008 dimensions must be followed.

Flue Terminal Positions

Min. Spacing*

1. Directly below, above or alongside an opening

window, air vent or other ventilation opening. 300mm (12”)

2. Below guttering, drain pipes or soil pipes. 25mm ( 1”)*

BS5440-1 2008 75mm (3”)

3. Below eaves. 25mm (1”)*

BS5440-1 2008 200mm (8”)

4. Below balconies or a car port roof. 25mm (1”)*

BS5440-1 2008 200mm (8”)

5. From vertical drain pipes or soil pipes. 25mm (1”)*

BS5440-1 2008 150mm (6”)

6. From an internal or external corner or to a 25mm (1”)*

boundary along side the terminal. BS5440-1 2008 300mm (12”)

7. Above adjacent ground, roof or balcony level. 300mm (12”)

8. From a surface or a boundary facing the terminal. 600mm (24”)

9. From a terminal facing a terminal. 1,200mm (48”)

10. From an opening in a car port

(e.g. door or window) into dwelling. 1,200mm (48”)

11. Vertically from a terminal on the same wall. 1,500mm (60”)

12. Horizontally from a terminal on the wall. 300mm (12”)

Vertical Terminals

13. Above the roof pitch with roof slope of all angles. 300mm (12”)

 Aboveatroof.  300mm(12”)

14. From a single wall face. 300mm (12”)

From corner walls. 300mm (12”)

15. Below velux window 2000mm (79”)

16. Above or side of velux window 600mm (24”)

Table 4 - Balanced Flue Terminal Position

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Morco GB30 SII in the language / languages: English as an attachment in your email.

The manual is 6,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Morco GB30 SII

Morco GB30 SII User Manual - Dutch - 10 pages

Morco GB30 SII User Manual - French - 10 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Morco GB30 SII Manual

Product: