653302
19
Zoom out
Zoom in
Previous page
1/36
Next page
19
section 5 - installation instructions
 
 
For side outlet refer to section 1.2 before connecting.
1. Makesurethat‘tophat’onthecollar(A)tsoverthe
rectangular form on the inner plastic pipe (B).
2. Ensurethattheatbaseofthecollar(C)is
positioned on the bottom lip of the pipe (D).
INNER PIPE ASSEMBLY INSTRUCTIONS
3. Slide the pipe and collar assembly back into the outer
housing (E), note that this can only be done at the female
end of the outer housing.
4. Whenttingsupportbrackets(F)makesuretheyare
positioned on the female side of the neck as shown.
A B
Top Hat
Rectangular
C
D
E
F
Theuedeectorelbowcanbettedtotheueoutletofthestandard
terminalkitsRSF303orRSF305todeecttheueproductshorizontally
to the left or the right only.
1. RefertotheboilerInstallationandServicingInstructionsforttingof
theboileranditsuesystem.
Note. The resistance of the deector is equivalent to 1 metre of ue
length. Ensure this is used when calculating the maximum allowable
ue length.
2. Choosethedirectionrequiredtodeecttheueproducts
(horizontally left or right only).
3. Pushthedeectorelbowontotheangledueoutletoftheterminal
inthedesiredpositionandensurethedeectorispusheduptothe
shoulder to fully engage the rubber seal. Drill the terminal through
theholeinthedeectorwitha3.2mm(1/8")drillandsecurethe
deectorwiththeselftappingscrewprovided.
Note. Only use water as a lubricant during assembly. Do not use
mineral based oils.
 
This optional kit can be used on both horizontal and
verticaluekits
1. Use dimensions below for calculating total length
2. Whencuttingextensionsoruekitsalwaysallow
sufcient(+30mmairduct+14mmueduct)to
allowforcorrectengagementinthetting
3. 1 elbow reduces the maximum available length by
1m
Note. Only use water as a lubricant during assembly .
Do not use mineral based oils.
Flue
Deector
WALL
115
115
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Morco GB30 Series II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Morco GB30 Series II in the language / languages: English as an attachment in your email.

The manual is 6,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info