646330
28
Zoom out
Zoom in
Previous page
1/36
Next page
28
SECTION 7 - ROuTINE SERvICINg INSTRuCTIONS
3
7.6
CLEANING THE HEAT EXCHANGER
Note: Ensure the condensate trap/siphon
is fully drained before cleaning. Refer to
Frames 7.5.
1. Removeignitionandamedetection
electrodes.RefertoFrames7.9&7.10.
2. It is advisable to replace the sump cover
priortothewaterushprocess.
3. Thoroughlyushtheheatexchanger
by pouring water into the top of the
combustion chamber ensuring the full top
area is covered.
4. Remove the sump cover and clean loose
deposits from the sump.
5. Inspect the ignition and detection
electrodes. Ensure that they are clean
and in good condition - replace if
necessary.
6. Re-ttheignitionandamedetection
electrodes. Ensure that earth wire is
connected to the electrode
7. Check that the ignition and detection gaps
arecorrect.RefertoFrames7.9&7.10.
1
Ignition Electrode
Earth Wire
Flame Detection
Reassemble the boiler in the following order:
1. Ensure that the condensate trap/siphon is full of water.
2. Rettheburnerensuringthesealinggasketiscorrectly
positionedandfreefromdamage(tightenthe4xingscrews
in the sequence A,B,C,D, shown below).
3. Retthefan/venturiassemblyensuringtheretainingtabs
are correctly positioned and the sealing gasket is correctly
positioned and free from damage.
4. Reconnect the fan electrical leads.
7.7
REASSEMBLY
5
A
5. Removethesumpcoverandrettheloweruemanifold
as shown.
6. Retthesumpcover.
7. Rettheboilerupperandlowerfrontpanels.
IMPORTANT. Ensure that the boiler upper front panel
iscorrectlyttedandthatagoodsealismade.Replace
seals as necessary.
8. Turn on the gas supply at the gas service cock.
9. Reconnect the electrical supply.
C
B
D
28


Need help? Post your question in this forum.

Forumrules
1

Forum

morco-gb24

Reset search

  • How can you tell what the temperature is on the boiler ? Submitted on 7-2-2022 at 14:04

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Morco GB24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Morco GB24 in the language / languages: English as an attachment in your email.

The manual is 7,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Morco GB24

Morco GB24 User Manual - English - 8 pages

Morco GB24 User Manual - Dutch - 10 pages

Morco GB24 User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info