646330
14
Zoom out
Zoom in
Previous page
1/36
Next page
14
section 5 - installation instructions
5.1 BOILER PACKAGING
The boilers are supplied in different packagings:
• Boiler
• FlueSystem(separate)
• HardwarePack(separate)
5.2 FITTING/MOUNTING THE BOILER
Decidewheretheboileristobexedonthewall,takinginto
account installation requirements detailed in previous section.
1. Screw the wall mounting plate to the wall choosing one of the
two sets of slots in left and right bank. Ensuring that at least
oneofthescrewsisttedintoatopslot.
2. Lift the boiler onto the wall mounting plate, locating it over the
two tabs.
Note. If present, remove the bottom end support packaging
and ensure all plastic plugs are removed from CH & DHW
connections.
5.3 WIRING INSTRUCTIONS
WARNING: THIS APPLIANCE MUST BE EARTHED
Connections must be made in such a way that allows complete
isolation of the electrical supply, e.g. double pole switch with
3mm contact separating in both poles.
N
L
N
ROOM
STAT/
TIMER
Room
Stat
5.4 INTERNAL WIRING
Theboilerhasbeenpre-ttedwitha3ampfusedapproved
moulded3pinandyingleadforusewith230V50Hz.
If the supply cord is damaged, it must be replaced by the
manufacturer,itsserviceagentorsimilarlyqualiedpersonsin
order to avoid a hazard.
The plug should be used with an
unswitched/shuttered socket outlet
complying with BS1363.
Theboilercomespre-ttedwith
a link wire between the room
thermostat/Timer connections on
the terminal strip. This creates a
permanent call for heat and must
be removed when adding a room
thermostat.
ROOM THERMOSTAT - WIRING
Totaroomthermostatproceedasfollows:
1. Ensure that the electrical supply to the boiler is isolated before
proceeding.
2. Removethetwoscrewsbeneaththeaponthefrontofthe
boiler and lower the front panel.
3. Removethepre-ttedlinkwirebetweentheRoomstat/timer
terminals.
4. Pass the cable through a grommet, secure with the cable
clamp and connect the room stat as shown in the diagram
below.
5. If room stat has a neutral connection, connect this to terminal
N (load) in the fused spur.
6. Carry out all necessary electrical checks.
7. Raise the front panel and relocate the two screws under the
smallap.
8. Check operation of room stat if possible.
Example of fixing
4
Cable
Clamp
14


Need help? Post your question in this forum.

Forumrules
1

Forum

morco-gb24

Reset search

  • How can you tell what the temperature is on the boiler ? Submitted on 7-2-2022 at 14:04

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Morco GB24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Morco GB24 in the language / languages: English as an attachment in your email.

The manual is 7,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Morco GB24

Morco GB24 User Manual - English - 8 pages

Morco GB24 User Manual - Dutch - 10 pages

Morco GB24 User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info