481109

Montiss CSC5623M Manual

21
Zoom out
Zoom in
Previous page
1/51
Next page
21
USE OF ACCESSORIES
English
Steam-output indicator (Illustration 3)
With the steam-output indicator you can determine the steam emission. It is possible to set the
output of steam between MIN (minimum); no steam and MAX (maximum).
Should no steam be emitted from the unit during use, then check:
- The setting of the steam-output indicator.
- If the unit has been switched on and has reached the selected temperature.
- If the steam output has been locked (see “Safety Lock”)
- If all the connecting pieces have been properly assembled.
- If the steam hose has been properly attached to the unit.
Should the above-mentioned check not result to release of steam, please switch the device off and
pull the plug from the wall socket. Let the device cool down completely and then check if there is
water in the tank. If not, please fill the unit as described at the header “filling the water tank”.
Should there be sufficient water in the tank, please start using the device once more. If there is
still no steam coming from the unit, then please contact us.
Steam Gun (Illustration 4)
Before you can start using the device, please ensure the steam hose has been connected to the
unit correctly. You can also do this after you have fixed accessories to the steam gun. Pull down
the lid of the steam socket at the front and insert the hose in a proper manner by lining up the 4
ridges. Push the two pieces well into each other.
The cleaner is ready for use when the yellow steam ready switches off. Ensure that the safety lock
on the steam gun is off. When you press the trigger on the steam gun, steam will be emitted from
the nozzle. Direct the steam gun at a cloth first, until the steam is emitted evenly. Now keep the
trigger pressed, and direct the steam jet at the surface to be cleaned, removing the dirt by moving
the steam jet to and fro over the surface. The steam jet will stop as soon as you release the steam
trigger.
Safety Lock (Illustration 5)
When the safety lock is pushed to the forward position, the steam switch cannot be pressed. Push
the lock to the rear position to release the steam switch.
In order to ensure safe use, even in case of accidental contact with liquids, the steam gun is
isolated from the electrical power supply (zero-volt system).
When cleaning surfaces with the steam gun, wipe the surface dry afterward using a micro-fibre or
cotton cloth if necessary; this will also remove any excess moisture for thorough cleaning. In order
to control the steam output and cleaning power at the surface, move the steam gun closer to or
further away from the surface. Do not hold the steam gun concentrated for too long on a single
spot.
Extension tubes (Illustration 6)
Depending on the task in hand, you can fit one, two or three extension tubes. Push the extension
tube onto the connection nozzle as far as it will go until you hear it click into place. Then attach
the floor head.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Montiss CSC5623M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Montiss CSC5623M in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info