584630
11
Zoom out
Zoom in
Previous page
1/18
Next page
Positioning/Initial Set Up
Leave the subwoofer unplugged from the mains until the installation procedure is completed. The
subwoofer should now be sited in the most suitable position, preferably not directly in the corner of the room as
this may cause excessive bass ‘boom’. Once a desirable position is achieved it is important to check if the cables
are long enough to reach comfortably without being under tension. The optimal control settings will depend
entirely on your system configuration. For initial trials set the controls as follows:
Volume Control Should be set to minimum
Frequency Control Should be set to the minimum position (40Hz)
Phase Control Should be set to zero degrees
Power Mode Switch (R370
HD
Only) Should be set to ‘Auto’ (if not using 12v trigger)
EQ Setting (R370
HD
Only) This will be set as EQ1 by default when powered up
Mode setting (R360
HD
Only) This should be set to Music:
Low Pass Filter Switch (R370
HD
Only) Should be set to the ‘Out’ position
Input connections can be made at this stage before the power is connected to the subwoofer. Do not connect
the 12v trigger yet.
Never connect or disconnect any leads with the subwoofer switched on.
Set Up
Once the input cables are connected and the controls are set in accordance with the initial set-up procedure
above, the subwoofer can be connected to the mains power supply and switched on at the mains power switch.
Do not play any music at this stage. Power Mode Switch in the ‘Auto’ position, the unit should remain in standby
with the power LED on the amp panel should be red, and the EQ1 button illuminated blue (R370
HD
only) until the
AV amp is turned on or a signal is received.
To manually set up you sub, play a variety of music/ film excerpts that you are familiar with starting at a very low
volume level, increasing to an average listening level once you are sure everything is working correctly. Please
now follow the instructions below: -
For use with an AV amp/receiver (product with Subwoofer output) please select the low pass filter switch to •
the ‘Out’ position. Otherwise select low pass filter switch to the ‘On’ position. This engages the crossover
frequency control on the subwoofer (please refer to pages 5 & 7).
If u• sing the crossover frequency control please adjust in accordance with the table on page 6. Further fine-
tuning may be required.
The Phase Control can now be set, please refer to pages 5 & 7 for further information.•
It is important to try a variety of music and film excerpts with which you are familiar in order to obtain the optimum
overall settings.
A lot of AV amplifiers/ receivers have an auto set up on them. If you use this to set up your sub, please remember
to go back into the settings of your AV amp and check them. You may need to go back and set it up manually,
both on the sub and on the AV amp.
12v Trigger (R370
HD
only)
When you are happy with the set up of your R370
HD
, turn off both the source and your sub woofer. Connect the
supplied lead to your amp and your sub. The Power Mode Switch on the R370
HD
can be left in any position. The
Mains Power Switch should be left in the ‘on’ position. With the trigger connected, the sub will turn on when
the source is turned on and will stay until the source is turned off. This is the most energy efficient way of using
your sub woofer.
9
monitoraudio.co.uk
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Monitor Audio 360hd at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Monitor Audio 360hd in the language / languages: English as an attachment in your email.

The manual is 2,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info