493641
40
Zoom out
Zoom in
Previous page
1/48
Next page
EN-40
(a)
(b)
(c)
(c)
Replacing the lamp (continued)
To replace the lamp:
1. Turn off the main power switch and unplug the power cord.
2. Reverse the projector gently.
3. Loosen the screw (a) using a Phillips screwdriver (+), and
remove the lamp cover (b).
4. Loosen the screws (c) using a Phillips screwdriver (+).
5. Pull up the handle.
6. Pull out the lamp box by the handle while holding the
projector.
Pull the lamp box out of the projector slowly. If it is
pulled out quickly, the lamp may break scattering glass
fragments.
Do not spill liquid on the removed lamp box or do not
place it near any fl ammable object or where children
can reach to prevent injury or fi re.
7. Load a new lamp box securely into the projector in the right
orientation.
8. Put the handle back to the original position.
Make sure that the handle is locked.
9. Tighten up the screws (c) using a Phillips screwdriver (+).
10. Tighten up the screw (a) using a Phillips screwdriver (+) to
secure the lamp cover.
Reset of the lamp operation time
11. Plug the power cord into the wall outlet and turn on the
main power switch.
12. Hold down the
W
,
X
, and POWER buttons on the control
panel at the same time about 3 seconds.
Important:
Unless these 3 buttons are held down at the same time, the lamp operation time isn’t reset.
Make sure that the STATUS indicator is lit twice and the lamp operation time is reset successfully.
The projector doesn’t turn on if the lamp cover isn’t attached securely.
Be sure to reset the lamp operation time whenever you replace the lamp.
Do not reset the lamp operation time unless you replace the lamp.
The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.
Contact your dealer for a new lamp.
This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be
regulated due to environmental considerations. For disposal or recycling information, please contact your local
authorities or the Electronic Industries Alliance: www.eiae.org. (For the U.S. only.)
(a)
Handle
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi XL6600U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi XL6600U in the language / languages: English as an attachment in your email.

The manual is 4,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info