493634
29
Zoom out
Zoom in
Previous page
1/45
Next page
EN-29
ENGLISH
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500 m –3000 m above sea
level, and temperature is between 0°C–35°C.
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature is between 0°C and 35°C. The
projector will be over cooled, if you turn the mode on under such condition.
To activate the High Altitude Mode:
1. Press MENU and then press / until the SYSTEM SETUP:
Advanced menu is highlighted.
2. Press to highlight High Altitude Mode and press / to select On.
A confirmation message displays.
3. Highlight Yes and press MODE/ENTER.
Operation under "High Altitude Mode" may cause a higher decibel operating
noise level because of increased fan speed necessary to improve overall system
cooling and performance.
If you use this projector under other extreme conditions excluding the above, it may display auto shut-down
symptoms, which is designed to protect your projector from over-heating. In cases like this, you should switch to
High Altitude Mode to solve these symptoms. However, this is not to state that this projector can operate under any
and all harsh or extreme conditions.
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect
the projection settings, operation, or performance.
Menu display time in the SYSTEM SETUP: Advanced > Menu Settings menu sets the length of time the
OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second
increments. Use / to select a suitable time frame.
Menu position in the SYSTEM SETUP: Advanced > Menu Settings menu sets the OSD position in five
locations. Use / to select a preferred position.
Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OSD menus. Use / to
select your language.
Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be displayed during
projector start-up. Use / to select a screen.
Shutting down the projector
1. Press Power and a confirmation message displays prompting you.
If you don't respond in a few seconds, the message will disappear.
2. Press Power a second time. The POWER indicator light flashes
orange, the projection lamp shuts down, and the fans will continue to run
for approximately 90 seconds to cool down the projector.
3. Once the cooling process finishes, the POWER indicator light is a
steady orange and fans stop.
4. Disconnect the power cord from the wall socket if the projector will not
be used in an extended period of time.
To protect the lamp, the projector will not respond to any commands during the
cooling process.
To shorten the cooling time, you can also activate the Quick Cooling function.
See "Quick Cooling" on page 33 for details.
Do not unplug the power cord before the projector shutdown sequence is
complete or during the 90-second cooling down process.
If the projector is not properly shut down, to protect the lamp, when you attempt
to re-start the projector, the fans will run for a few minutes to cool down. Press
Power again to start the projector after the fans stop and the POWER
indicator light turns orange.
I
I
I
I
I
I
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi XD95U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi XD95U in the language / languages: English as an attachment in your email.

The manual is 2,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info