549867
73
Zoom out
Zoom in
Previous page
1/79
Next page
EN-73
Indicators
This projector has 5 indicators, each of which shows the operation condition of the projector.
The following offer solutions to possible problems. If these problems persist, turn the projector off and consult your
dealer.
POWER indicator
FILTER indicator
LAMP 1 indicator
STATUS indicator
LAMP 2 indicator
POWER, STATUS, and FILTER: The current condition is indicated.
POWER STATUS FILTER CONDITION POSSIBLE SOLUTION
Normal
condition
Steady red Off Off
Power standby or cooling
Steady green Off Off
The power is on (Normal condition) The lamp condition is indicated by
the LAMP indicators.
Abnormal
condition
Blinking green/
red
Off Off
• Anyofthelampcoverandltercover
is open.
• Closeallthecovers.
Steady
*1
or
Blinking
*1
Abnormal Contact your dealer.
Steady red
or
Steady green
Blinking orange Off
Abnormal temperature
• Theventsarecloggedwithdustor
dirt.
• Theroomtemperatureishigh.
• Thelterisdirty.
• Cleanthevents.
• Relocatetheprojectortoacooler
place.
• Cleanthelter.(Seepage67.)
*1: Status of either or both of the indicators.
LAMP 1, LAMP 2: The condition of each lamp is indicated.
LAMP 1 / LAMP 2
CONDITION POSSIBLE SOLUTION
Normal
condition
Blinking green
•
When the lamp is illuminating, it is in the
warmup mode. (You cannot turn off the
power.)
•
When the lamp is off, it is in the cooling
mode. (You cannot turn on the power.)
Steady green
The lamp is illuminating.
Replacement
Blinking red
or
Blinking green/red
Lamp operation time warning. (Total lamp
operation time reached 3000 hours
*2
.)
Replace the light source lamp indicated by the
illuminating or blinking indicator.
Change with a new lamp if this problem
recurs.
Steady red
Lamp operation time warning. (Total lamp
operation time reached 4000 hours
*2*3
.)
Abnormal
condition
Blinking orange
The protection circuit is working or the lamp
is in an abnormal condition.
When only one lamp fails:
•
In the case that LAMP SELECT is set to
DUAL, only the normal lamp illuminates
(the intensity of one lamp is obtained).
•
In the case that LAMP SELECT is set to
SINGLE, LAMP 1, or LAMP 2, only the
normal lamp illuminates (the lamp isn’t
switched).
When both indicators blink, wait until the
indicators stop blinking and then press the
POWER button. If the light source lamps don’t
illuminate even after you perform the above
operation several times, unplug the power cord
from the wall outlet and contact your dealer.
To illuminate the failed lamp again when either
indicator blinks, turn off the power and wait until
the indicator stops blinking and then press the
POWER button. If the light source lamp doesn’t
illuminate even after you perform the above
operation several times, unplug the power cord
from the wall outlet and contact your dealer.
*2:
Duration when LAMP MODE of the INSTALLATION 1 menu is set to LOW. When it is set to STANDARD, this duration will be shorted.
*3: When LAMP MODE is set to STANDARD, this duration will be shorted up to 2000 hours.
73


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi XD8500U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi XD8500U in the language / languages: English as an attachment in your email.

The manual is 10,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Mitsubishi XD8500U

Mitsubishi XD8500U Additional guide - English - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info