493655
10
Zoom out
Zoom in
Previous page
1/75
Next page
EN-10
Using the remote control (continued)
Setting the ID number of the remote
control
You can control multiple projectors collectively or
individually using one remote control by setting the ID
number (CONTROLLER ID) of the remote control.
To control multiple projectors using the remote
control, you need to select the projector’s ID number
(PROJECTOR ID) with the remote control in advance.
ID numbers should be two-digit numbers “01” to “63”
or “ALL.” Other numbers cannot be used.
For setting the ID number of the projector, see page
60.
ID button
Number (0 to 9)
buttons
ALL button
Setting by the remote control alone
1. While holding down the ID button on the remote
control, press the number buttons (0 to 9) to set a
two-digit ID number.
Or, while holding down the ID button on the remote
control, press the ALL button.
You cannot set the ID number by pressing the
number buttons (0 to 9) or the ALL button unless
pressing them while holding down the ID button
on the remote control.
You can set the CONTROLLER ID using the
remote control alone. When you set the ID with
the remote control directed to the projector, you
can see the setting status on the screen.
Setting by using the projector
1. Carry out the procedure described in “Setting by
the remote control alone” with the remote control
directed to the projector.
The ID setting dialog box is displayed on the
upper right area of the screen.
PROJECTOR ID XX
CONTROLLER ID
(01 - 63/ALL)
YY
o
ZZ
XX: Shows the ID number of the projector.
(When the PROJECTOR ID is “ALL,” “ALL”
is displayed.)
YY: Shows the current CONTROLLER ID. (When
the CONTROLLER ID is “ALL,” “ALL” is
displayed.)
ZZ: Shows the CONTROLLER ID to be changed.
(When the CONTROLLER ID is “ALL,” “ALL”
is displayed.)
Before a CONTROLLER ID is entered, ** is
displayed. When you press a number button (0
to 9), the left digit of the ID number is entered
rst.
When the CONTROLLER ID setting has succeeded:
PROJECTOR ID XX
CONTROLLER ID
(01 - 63/ALL)
YY
o
ZZ
COMPLETE
“COMPLETE” is displayed under the
CONTROLLER ID number you entered.
The ID setting dialog box automatically
disappears after it is displayed for about 5
seconds.
By pressing any button other than the ID button,
number buttons (0 to 9), and ALL button while
the ID setting dialog box is being displayed, you
can cancel the dialog box.
When the CONTROLLER ID setting has failed:
PROJECTOR ID XX
CONTROLLER ID
(01 - 63/ALL)
YY
o
ZZ
ERROR
“ERROR” is displayed under the CONTROLLER ID
number you entered.
The ID setting dialog box automatically
disappears after it is displayed for about 5
seconds.
By pressing any button other than the ID button,
number buttons (0 to 9), and ALL button while
the ID setting dialog box is being displayed, you
can cancel the dialog box.
Important:
ID numbers should be two-digit numbers “01” to
“63.” The other numbers are invalid.
When the PROJECTOR ID number is any of
“01” to “63,” you can control the projector
by matching the CONTROLLER ID with the
PROJECTOR ID number or setting it to “ALL.”
When the PROJECTOR ID number is “ALL,”
you can control the projector using the remote
control regardless of the CONTROLLER ID
number.
When the PROJECTOR ID number is uncertain,
you can control the projector regardless of the
ID number by setting the CONTROLLER ID to
“ALL.”
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi XD8100U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi XD8100U in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info