493596
23
Zoom out
Zoom in
Previous page
1/30
Next page
EN-23
ENGLISH
Troubleshooting
The following offers solutions to some of the common problems you may encounter. We suggest that you consult this chart before contacting your
dealer.
Images aren’t projected on the screen.
Problem Cause and solution
Power isn’t turned on.
Check the states of the indicators.
Images aren’t projected on the screen.
Cancel the AV mute by pressing the MUTE button.
Remove the lens cap.
The lamp sometimes takes about one minute to light up.
On rare occasion, the lamp fails to light up. In such cases, wait a few minutes and try to light the lamp again.
If the projector was turned off before the lamp cooled down completely, the fans may start rotating and the
POWER button may not function when you plug the power cord into the wall outlet next time. Wait for the
fans to stop and press the POWER button to turn on the lamp again.
Check that the lamp cover are closed.
Check that the cable connected to the external device isn’t broken.
When an extension cord is being used, replace it with the supplied cable and check whether images are pro-
jected correctly. If images are projected correctly, use an RGB signal amplifier along with the extension cord.
Images suddenly disappear.
The air inlet or outlet grille may be blocked. (In such cases, the STATUS indicator blinks orange.)
J Remove the objects blocking the air inlet or outlet grille and carry out the following.
1. Wait for the air inlet or outlet fan to stop (or wait for the STATUS indicator to go out.)
2. Unplug the power cord from the wall outlet.
3. Wait about 10 minutes.
4. Plug the power cord into the wall outlet.
5. Press the POWER button.
When the STATUS indicator is blinking red, it is indicating that the lamp should be replaced. Replace the
lamp in this case.
Check that AUTO POWER OFF has been set to OFF.
If the lamp has deteriorated, it may go out after a while it illuminates.
"NO SIGNAL" is displayed.
Turn on the power of the connected device, or check whether there is something wrong with the connected
device.
Check whether the external device outputs signals. (Check this especially when the external device is a note-
book computer.)
Check that the cable connected to the external device isn’t defective.
Check that the projector is connected to the external device using the correct terminals.
Check that the connected device is correctly selected as the input source.
When an extension cord is being used, replace it with the supplied cable and check whether images are pro-
jected correctly. If images are projected correctly, use an RGB signal amplifier along with the extension cord.
POWER
Off
Steady red
Blinking red
/ green
STATUS
Off
Off
Blinking
orange
Blinking
green
Steady red
Off
Steady
or
Blinking
Solution
If any objects are blocking the air inlet or outlet grille, remove them and carry out
the following.
1.
2.
3. Plug the power cord into the wall outlet.
4. Press the POWER button.
Replace the lamp. (The lamp is at the end of its life.)
Attach the lamp cover on the bottom.
Connect the power cord to the projector.
Plug the power cord into a wall outlet.
Unplug the power cord from the wall outlet.
Make sure that the projector has cooled off.
If any objects are blocking the air inlet or outlet grille, remove them.
Don't expose the air outlet grilles to hot air emitted from a heating appliance.
After the STATUS indicator stops blinking, press the POWER button.
If you unplug the power cord while the fan is rotating, the lamp may not turn on about
one minute when you plug the power cord next time.
The lamp can't turn on again for one minute after it goes out.
Press the POWER button several times.
Unplug the power cord from the wall outlet and contact your dealer.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi XD470U-G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi XD470U-G in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info