493630
16
Zoom out
Zoom in
Previous page
1/31
Next page
EN-16
Displaying thumbnails
1. Connect a USB memory stick to the [USB VIEWER] termi-
nal on this device.
2. Select a USB viewer.
Press the [VIEWER] button on the remote controller or the
[COMPUTER] button on the main unit. The selection will
change between “COMPUTER1” “COMPUTER2” “USE
VIEWER” each time you press the [COMPUTER] button.
Data is read from the connected USB memory stick and
thumbnails appear in the screen.
The method to display thumbnails can be changed from the
menu setting. If you want to display thumbnails, set
[THUMBNAIL DISPLAY] under [SLIDE SHOW SETTING] to
“ON” and, if not, set it to “OFF”.
3-1. Displaying JPEG images
Display thumbnails in the thumbnails screen.
Move the red frame using the
W, X,T buttons to select the
file you want to play (show) and press the [ENTER] button.
The image changes and a slide appears.
To open a folder, move the red frame to the target folder and
press the [ENTER] button.
You can move to a folder located 3 levels lower in the same
method.
* You cannot open a folder at the lowest level (3rd level).
To return to folder at a higher level, move the red frame to a
folder indicated with a [RETURN] mark and press the
[ENTER] button.
Use the [
X] or [W] button to change the displayed slide. ([W]
displays the previous slide and [
X] displays the next slide.
These buttons cannot be used during a slide show.) Non-
supported files (magnifying glass display) or movie files will
be skipped.
Pressing the [
S] button rotates the displayed slide in incre-
ment of 90 degrees to the right. The rotation data is not
applied to a different slide or images in a different folder.
Press the [Enter] button to return to the thumbnail display.
3-2. Starting a slide show
If [AUTO START] in the [SLIDE SHOW SETTING] menu is set
to “ON”, a slide show will start by inserting a USB memory
stick and changing the input mode to “USB Viewer”, or if the
input mode is preset to “USB Viewer”, a slide show will start
immediately when a USB memory stick is inserted.
A slide show can be started when [AUTO START] is set to
“OFF” by displaying a JPEG image and pressing the [
T] but-
ton. A slide show will start from the file currently displayed.
Press the [Enter] button to return to the thumbnail display.
Press the [STILL] button to pause a slide show. The paused
status can be cleared by pressing any button other than the
[ENTER] button.
Other than the above, the [SLIDE SHOW SETTING] menu
offers [REPEAT SETTING], [INTERVAL TIME], and [TRANSI-
TION EFFECT] settings.
The file subjected to the slide show is the JPEG file in the cur-
rent folder.
3-3. Playing an MPEG format
Select a movie file you want to see from the thumbnail display
and press the [ENTER] button in the same way as displaying
a JPEG image.
Press the [ENTER] button to stop the MPEG display and
return to the thumbnail display. The thumbnail display will also
return automatically when the MPEG display is over.
4. Disconnecting a USB memory stick
Press the [UNPLUG] button on the remote controller, or select
“Disconnect device” in [SLIDE SHOW SETTING] and press
the [OK] button.
A message confirming if you want to remove the USB mem-
ory stick will appear, so use the [
X] or [W] button to select
“Yes” and press the [ENTER] button.
Remove the USB memory stick after the message saying
“This USB device can be removed safely” appears.
Important:
The order of thumbnail and slide show display is from file names
set with the fewest number of characters. If the same number of
characters is used, it will be in the numerical order, and then,
alphabetical order.
If a non-supported file (magnifying glass display) exists in the
thumbnail display, the image cannot be displayed. It will be
skipped automatically in a slide show.
Movie files are not subjected to a slide show. They will be skipped
automatically as well.
Only single-byte numbers, alphabets, and some symbols can be
used in a file or folder name. Non-supported characters will be
replaced with a question mark “?”.
When you unplug USB devices, be sure to perform unplug opera-
tions either from a remote controller or from a menu.
Sometimes, USB device may not be recognized. If this is the
case, turn on the power of the main unit again.
To use the auto-start function, place a JPEG image file on the top
hierarchy.
Depending on JPEG files, the display interval during slide shows
may exceed the interval time.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi XD435U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi XD435U in the language / languages: English as an attachment in your email.

The manual is 1,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info