493654
46
Zoom out
Zoom in
Previous page
1/53
Next page
EN-46
Troubleshooting
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be
sure to unplug the power plug, and then contact your dealer.
No image appears on the screen.
Problem Solution
Power can not be
turned on.
Check whether the indicators are on or off and how they are lightning.
POWER STATUS Solution
Off Off
• Connect the power cord to the projector.
• Plug the power cord into a wall outlet.
• Turn on the main power switch.
• Attach the lamp cover.
Steady red
Off
• If any objects are blocking the air inlet or outlet grille, remove them and carry out
the following.
Turn off the main power switch.1.
Make sure that the projector has cooled off. 2.
Turn on the main power switch.3.
Press the POWER button.4.
Blinking
orange
• If any objects are blocking the air inlet or outlet grille, remove them.
• Don’t expose the air outlet grilles to hot air emitted from a heating appliance.
Blinking
green
• After the STATUS indicator stops blinking, press the POWER button.
If the main power switch is turned off while the fan is rotating, the lamp may not turn on
about 2 minutes when the main power switch is turned on next time.
The lamp can’t turn on again for 2 minutes after it goes out.
• Press the POWER button several times.
Steady red
• Replace the lamp. (The lamp is at the end of its life.)
Blinking
red/green
Steady
or
Blinking
• Unplug the power cord from the wall outlet and contact your dealer.
No image appears on
the screen.
Cancel the AV mute by pressing the AV MUTE button.
Check that the lens cap is removed.
It may take about 1 minute for the lamp to light up.
The lamp fails to light up on rare occasions. In such a case, wait for a few minutes
and then try again.
If the projector was turned off before the lamp was cooled down suf ciently last time,
the fan may start rotating and the POWER button may not work after the main power
switch is turned on. After the fan stops rotating, press the POWER button to turn back
on the POWER indicator.
Set SCART INPUT in the QUICK MENU or FEATURE menu to OFF. (See pages 27 and
31.)
Check that the intake vent is clean.
Check that the cables connected to the external devices are not broken.
When an extension cable is being used, replace it with the supplied cable for check.
When images are displayed correctly, add an RGB signal amplifi er to the extension
cable.
Power turns off. This problem may occur when the intake vent and/or exhaust vents are blocked. (In
such a case, the STATUS indicator brinks orange.)
J Remove the objects blocking the intake vent and/or exhaust vents and then carry
out the following procedure.
1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS indicator
goes out.)
2. Turn off the main power switch.
3. Wait about 10 minutes.
4. Turn on the main power switch.
5. Press the POWER button.
When the STATUS indicator is steady red, it is indicating that the lamp should be
replaced. Replace the lamp in this case.
Check that AUTO POWER OFF has been set to OFF.
If the lamp has deteriorated, it may go out after a while it illuminates.
The screen for
entering the password
appears.
PASSWORD FUNCTION in the FEATURE menu has been set to DISPLAY INPUT to
enable the password lock.
J Enter the password or contact the person in charge of management of the
projector. (See page 38.)
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi XD3500U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi XD3500U in the language / languages: English as an attachment in your email.

The manual is 2,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Mitsubishi XD3500U

Mitsubishi XD3500U Additional guide - English - 17 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info