579853
15
Zoom out
Zoom in
Previous page
1/41
Next page
EN-15
ENGLISH
POWER
MENU
ENTER
STATUS
AUTO POSITION
COMPUTER
ZOOM/FOCUS LENS SHIFT
KEYSTONE
VIDEO
VOLUME
C. Projecting images
Preparation:
Remove the lens cap.
1. Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red.
If the projector was turned off before the lamp was cooled down suf ciently last time, the fan may start rotating
and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks
green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator.
2. Turn on the power of the connected computer.
3. Press the POWER button.
It may take about 1 minute for the lamp to light up.
The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the
lens cap.
After the POWER button is pressed, the image may fl icker before the lamp becomes stable. This is not a prod-
uct malfunction.
Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated
by default whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode
changes from STANDARD to LOW about 1 minute after turn-on.
The projector starts warming up when the POWER button is pressed. During the warm-up process, images
may appear dark and no commands are accepted.
By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when
the STATUS indicator blinks red. (See page 34 and 37.)
4. Press the ZOOM/FOCUS button on the projector or on the remote control to display “FOCUS”.
5. Adjust with the
or button to get a fi ne picture.
6. Select an input source.
Press the COMPUTER button on the projector or the COMPUTER1, COMPUTER2 or DVI-D(HDCP) button on
the remote control that is corresponding to the terminal in use.
The input source is switched from COMPUTER1 to COMPUTER2 to DVI at every press of the COMPUTER
button on the projector.
The projector automatically selects the appropriate signal format. The selected signal format is displayed on
the screen.
The COMPUTER and VIDEO buttons don't function while the menu is being displayed.
Though it may take some time before an image is displayed on the screen depending on the type of the input
signal, such symptom is not a malfunction.
Images may not be projected in the correct position, depending on the type of the input signal. In such a case,
press the AUTO POSITION button. (See page 16.)
When COMPUTER1 or COMPUTER2 is chosen as the source, images supplied from the computer may fl icker.
Press the or button on the remote control to reduce fl icker, if it occurs.
7. Adjust the position of the projector to keep an appropriate projection distance with which images are projected in
their specifi ed sizes.
8. Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.)
When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 10.)
9. Press the ZOOM/FOCUS button on the projector or on the remote control to display “FOCUS” and then press the
button again to display “ZOOM.”
10. Adjust with the or button to get an approximate size.
11. Press the LENS SHIFT button. "LENS SHIFT" will appear on the display.
12.Press the
or
button to adjust the vertical position and
or button to adjust the horizontal position of the
displayed image.
Repeat steps 4, 5 and 9 to 12, if necessary.
Important :
Focus, zoom and lens shift adjustment is possible in the normal picture mode only. In PinP or EXPAND mode, the
adjustment is prohibited.
When you press the ZOOM/FOCUS button or LENS SHIFT button while no signal is supplied, a blue background
screen is displayed.
When a 16:9 image is kept displayed for a long time before displaying 4:3 image, the afterimages of the black bars
may appear on the 4:3 image screen. Consult your dealer in this case.
POWER button
COMPUTER button
COMPUTER1, 2 buttons
DVI-D(HDCP) button
POWER button
ZOOM/FOCUS button
LENS SHIFT button
Main power switch
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi XD1000U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi XD1000U in the language / languages: English as an attachment in your email.

The manual is 5,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info