475290
131
Zoom out
Zoom in
Previous page
1/140
Next page
82
83
Problem Possible Solution
42. All IEEE 1394 devices disappear. • When connecting the devices, there must always be a device at the
end. The connected devices must not be in a loop that returns to the
TV.
• Disconnect all the cables and devices from the TV. Replace them one
by one to locate the problem device or cable.
• Use System Reset (front control panel).
43. Cannot rediscover a deleted IEEE 1394 device • The device has been disconnected. Plug it in.
• The device is unchecked in the Review screen. Go to Setup in the
Main menu, then select Review. Check the device.
• Remove IEEE 1394 plug. Go to the Edit NetCommand menu. Delete
the IEEE 1394 device. Plug the device in again so it can be
discovered again.
44. An IEEE 1394 device has been plugged in but
does not appear in the Device Selection menu
(not discovered).
• The IEEE 1394 connection to the TV or another device is loose.
• The IEEE 1394 device is not powered on.
• A device in the IEEE 1394 chain is not powered on - turn on all
devices.
• The device discovery can take as long as a minute to initiate.
• IEEE 1394 cable is too long (maximum of 15 feet between devices).
• The IEEE 1394 device uses an incompatible protocol and will not be
discovered
45. Cannot record to or from the IEEE 1394 device,
including Dub recordings.
• To initiate a recording to IEEE 1394 device press the REC key.
The Record menu displays allowing setup of the recording.
• The source device for the recording is not powered on.
• When dubbing, the destination device for the recording
is not powered on.
• The wrong media, (analog tape for digital recording, or
digital tape for the analog recording) is in the device.
• Either the program is copy protected, or if there are multiple
subchannels and one of the programs (not necessarily the
program requested) is copy protected.
• The program has already been recorded once and the copy
protection only allows one recording.
• Unapproved source device for copy protected material.
• The recording device can not decode the copyright signal
included in the signal source (try another device if available).
• The playing device (for dubbing) does not support
copyrighted material.
• Source for recording is copyrighted.
• Too many IEEE 1394 devices in network. Insufficient
bandwith available. Disconnect unused devices.
• Source Device has higher speed (S 400) than record device. If
possible, reverse devices, play in the slower device and record
in the faster device.
46. Cannot control the IEEE 1394 device from the
Transport Menu.
• Device may not support the command.
• Selected function is gray (such as Record for a DVD, which does not
support the Record function).
47. TV is not responding, after pulling out a Memory
card during playback.
• Press STOP or wait until playback is complete before removing
Memory card.
48. TV can’t play or stop a Memory Card. • NetCommand was not set up. Without NetCommand enabled, you
can only use ENTER to play and CANCEL on the TV remote to control
the Memory cards.
49. Can’t see a thumbnail picture in the JPEG
menu, or can’t see a track/song name in the
Playlist menu.
• File does not meet file standards for playback.
131


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WL-82913 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WL-82913 in the language / languages: English as an attachment in your email.

The manual is 10,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info