475290
37
Zoom out
Zoom in
Previous page
1/140
Next page
36
37
Connecting the IR Emitter NetCommand
®
or IR Repeater
  



 
     
   


 


 

 
 

 

Figure 16. Connecting IR Emitter NetCommand or IR
Emitter Repeater
IR Emitter NetCommand
®
or IR
Emitter Repeater
Figure 16
IR Emitter NetCommand
The emitters connected to these jacks are used by the
NetCommand system to control other devices such as
VCR, DVD players, Cable boxes and Satellite receivers.
1A.Connect the plug end of the supplied Quadruple IR
Emitter Cable to one of the IR Output NetCommand
jacks on the TV back panel.
OR ...
IR Emitter Repeater
The emitters connected to these jacks are not used by
NetCommand, but will repeat any IR command received
by the TV. These emitters allow the TV to be the remote
control sensor for other devices outside the range of the
hand-held remote control. Do not use these repeaters
with devices that can receive the remote control signal
directly, as the signals can interfere with each other.
1B.Connect the IR emitter to IR EMITTER-REPEATER on
the TV back panel.
If a single emitter end can be placed in a position that will operate more than one device, do
not use a separate emitter end for the additional device. A single device receiving remote
control signals from too many emitters or remote controls may not respond at all.
IMPORTANT
After you have used 1A or 1B,
2. Run the cable for each of the emitter ends under, along
side or over the top of each device to be controlled to
the area of the front where the remote control sensor is
located.
3. Place the emitter end in front of the remote control
sensor of the device to be controlled. The emitter bulb
should face the remote control sensor. This bulb emits
infrared light in a cone shaped pattern. The bulb needs
to be placed far enough from the remote control sensor
to allow the cone pattern to include the sensor.
The remote control sensor is usually behind the plastic
window of the front display panel. It is sometimes
visible when you look through the display plastic using a
flashlight and is normally a round or square cutout behind
the plastic. If you cannot see the sensor and the devices
Owner’s Guide does not specify the location, you can find
it by using the device’s remote control. Hold the remote
about 1/2 inch from the front of the device. Starting from
one end of the display window plastic, press the POWER
button.
If the device does not respond, move the remote control 1
inch toward the center and try again. Repeat this until the
device responds. Note this location then start over from
the other end of the display window plastic, repeating until
the device responds again. The remote control sensor
will be somewhere between these two positions. This
is usually enough accuracy for the placement of the IR
emitters.
4. With some devices, the emitter will work better
facing downward from the top of the device. Some
experimentation may be needed. If you are not going
to
be using all emitter ends, place the unused ends
behind the devices so that they cannot send signals to
the remote control sensors.
5. The emitter end being used can be secured in place
using double stick tape.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WL-82913 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WL-82913 in the language / languages: English as an attachment in your email.

The manual is 10,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info