32987
31
Zoom out
Zoom in
Previous page
1/110
Next page
31
Chapter 2. Connecting
Connecting the IR Emitter NetCommand
®
% * ( * 5 " -
46 33 06 /%
4
$)
"73FDFJWFS
0UIFS"7EFWJDF
0UIFS"7EFWJDF





Net Command
IR EMITTER
¸
',INK
¸
57CBDLQBOFMTFDUJPO
Figure 13. Connecting IR Emitter NetCommand
IR Emitter NetComman
Figure 13
A double IR Emitter cable is included with models
WD-52527 and WD-62527. A Quadruple IR Emitter cable is
included with models WD-52528 and WD-62528.
The emitters connected to these jacks are used by the
NetCommand system to control other devices such as
VCRs, DVD players, Cable boxes and Satellite receivers.
1. Connect the plug end of the supplied IR Emitter Cable
to either one of the IR Output NetCommand jacks on
the TV back panel.
2. Run the cable for each of the emitter ends under,
along side or over the top of each device to be
controlled to the area of the front where the remote
control sensor is located.
3. Place the emitter end in front of the remote control
sensor of the device to be controlled. The emitter
bulb should face the remote control sensor. This bulb
emits infrared light in a cone shaped pattern. The
bulb needs to be placed far enough from the remote
control sensor to allow the cone pattern to include
the sensor.
The remote control sensor is usually behind the plastic
window of the front display panel. It is sometimes
visible when you look through the display plastic using
a flashlight and is normally a round or square cutout
If a single emitter
end can be placed
in a position that
will operate more
than one device, do
not use a separate
emitter end for the
additional device.
A single device
receiving remote
control signals from
too many emitters
or remote controls
may not respond
at all.
IMPORTANT
behind the plastic. If you cannot see the sensor and the
device’s Owner’s Guide does not specify the location,
you can find it by using the devices remote control.
Hold the remote about 1/2 inch from the front of the
device. Starting from one end of the display window
plastic, press the POWER button.
If the device does not respond, move the remote control
1 inch toward the center and try again. Repeat this
until the device responds. Note this location then start
over from the other end of the display window plastic,
repeating until the device responds again. The remote
control sensor will be somewhere between these two
positions. This is usually enough accuracy for the
placement of the IR emitters.
With some devices, the emitter will work better
facing downward from the top of the device. Some
experimentation may be needed.
The emitter end being used can be secured in place
using double stick tape.
If you are not going to
be using all emitter ends, place
the unused ends behind the devices so that they
cannot send signals to the remote control sensors.
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD62528 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD62528 in the language / languages: English as an attachment in your email.

The manual is 9,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info