32987
27
Zoom out
Zoom in
Previous page
1/110
Next page
27
Chapter 2. Connecting


57CBDLQBOFM
"UUBDIPOMZPOFDBCMFUZQF
47JEFPSFDPNNFOEFEJGBWBJMBCMF
)46


7$3CBDLQBOFM
*GZPVS7$3IBTBWJEFPDIBOOFM
PS3'0/0''TXJUDITFUJUUP0''




*/
065
065
5808":41-*55&3
*ODPNJOH$BCMF




COMPONENT
YPbPr (480i/480p/720p/1080i)
INPUT
1
2
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DTV/CABLE/
F
DIGITAL
AUDIO
OUTPUT
CableCARD™ USE WITH ANT 1 CARD TOP
1
2
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
OUTPUT
AUDIO
OUTPUT
RECORD
OUTPUT
DVI
Analog Audio
1 2
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
SERVICE
PORT
MONITORLINK™/HDMI
VIDEO 480i/480p/720p/1080i
AUDIO PCM LINEAR
1
2
IEEE 1394
INPUT/
OUTPUT
Net Command
IR EMITTER
¥
(-JOL
¥
INPUT
3
$BCMF#PY
CBDLQBOFMTFDUJPO
*/
065





DTV/CABLE/
VHF/UHF
USE WITH
CableCARD
TM
ANT 1 / MAIN
ANT 2 / AUX
VCR Video and Audio to a Cable Box
Figure 6
A two-way RF splitter, 4 coaxial cables, right and left audio
cables and an S-Video or Video cable are required. These are
not included with the TV.
1. Connect the incoming cable to IN on the RF splitter.
2. Connect one coaxial cable from OUT on the RF splitter
to ANTENNA IN on the cable box back panel.
3. Connect one coaxial cable from OUT on the RF splitter
to ANT-1 MAIN on the TV back panel.
4. Connect one coaxial cable from OUT on the cable box
to ANTENNA IN on the VCR back panel.
5. Connect one coaxial cable from ANTENNA OUT on the
VCR back panel to ANT-2 AUX on the TV back panel.
6. To use the TV speakers with the VCR, connect a set of
audio cables from AUDIO OUT on the VCR back panel
to INPUT-1 AUDIO-LEFT (MONO) and AUDIO-RIGHT
on the TV back panel. The red cable connects to
the R (right) channel and the white cable connects to
the L (left) channel. If your VCR is mono (non-stereo),
connect only the white (left) cable.
Figure 6. Connecting a VCR to a Cable Box
Note: NetCommand® will assume your VCR is connected to inputs as shown on this page. If you use any
other inputs for your VCR or add a second VCR, this change must match in the NetCommand system. See Edit
NetCommand... in Chapter 3 for more information.
Connecting VCR Video and Audio to a Cable Box
7. Connect either an S-Video or Video cable from VIDEO
OUT on the VCR back panel to INPUT 1 VIDEO on the
TV back panel. Only one type of video cable should
be connected. S-Video is recommended, if available.
8. For NetCommand® controlled recordings, connect a
set of audio cables from AUDIO IN on the VCR back
panel to RECORD OUTPUT AUDIO-LEFT (MONO) and
AUDIO-RIGHT on the TV back panel. The red cable
connects to the R (right) channel and the white cable
connects to the L (left) channel.
9. Complete the NetCommand controlled recordings
connections by connecting a Video cable from VIDEO
IN on the VCR back panel to RECORD OUTPUT
VIDEO on the TV back panel.
Note: With this connection configuration, it is
possible to view live cable programs through the
VCR. For best picture quality, however, always view
live cable programs directly from the cable box
instead of the VCR.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD62528 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD62528 in the language / languages: English as an attachment in your email.

The manual is 9,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info