32989

Mitsubishi WD62527 Manual

98
Zoom out
Zoom in
Previous page
1/110
Next page
98
Chapter 6. Special Features
1. The TV remote control does not work. • Check that the batteries are installed correctly.
• Check that the selected switch is set to “TV”.
• Be no further than 20 feet from the TV when using the remote control.
• Program the remote control to operate the TV (Appendix C).
2. The TV takes several seconds to respond. • It is normal for digital channels to take longer to tune in.
• Press ENTER after a channel number to avoid delays.
• Use a 4 digit number for an over-the-air digital channel
• Use a 6 digit number for cable digital channels
3. Cable provider needs information to start
CableCARD™ service.
On the remote control, press TV MENU and then enter the numbers 999
to display the Host ID and CableCARD™ ID information.
4. You cannot access a channel. • Use number keys instead of CHANNEL up/down.
• Be sure the channel you want to view is in memory. See page 68.
• Check that the TV is turned to the correct device or antenna for that
channel, by pressing the DEVICE button.
• Make sure the V-Chip lock is off.
• If tuned to Digital channels, have physical channel in memory.
5. On-screen displays appear each time you
change a function.
This is part of normal TV operation.
6. You cannot program the TV to turn on
automatically (timer function)
• The TV may be locked.
• The clock may not be set.
7. There is no sound even when the volume is
turned up.
• Check audio source in Device Menu.
• Check to see if the MUTE button is on.
• The TV’s “Listen to:” setting may be set to SAP.
• Check that the “TV Speakers” setting is On in the Audio/Video menu.
8. NetCommand unable to learn specific device
keys.
• Device does not use IR format for remote control signal. ITT and RF
formats cannot be learned.
• Room lighting may affect the signal. Have the remotes very close (6
inches or less) to the TV during Learning.
• If using a Mitsubishi remote control make sure slide switch is not set
to TV position.
• Some but not all device key functions can be learned by
NetCommand. For example, POWER and PLAY may be learned, but
other functions may not.
• The signal from the remote control may not be strong enough. Insert
fresh batteries and try Learning again.
9. You have forgotten your V-Chip pass code. See Appendix A, Bypassing the V-Chip Lock.
10. Lamp indicator light is a steady red. Turn the TV off for at least 2 minutes. Turn back on. If light is still red,
the lamp has failed. Replace it. See Appendix H for lamp replacement
information.
11. Lamp indicator light is a steady yellow. Lamp’s elapsed time has exceeded 5,000 hours. Purchase a new lamp.
See Appendix H for lamp replacement information.
12. Lamp indicator light is a flashing yellow. Lamp cover door is open or lamp cartridge is not secure. See Appendix
H for lamp replacement information.
13. Status indicator light is a steady yellow. Operating temperature or room temperature has exceeded proper
levels. Clean the TV’s dust filter or cool the room. See Appendix G for
filter cleaning information.
14. Status indicator light is a steady/flashing red. • Service may be required. Turn off the TV and unplug the set from the
AC power source. Wait one minute and then plug the set back in.
• If the LED in still on, contact your dealer or a Mitsubishi Authorized
Service Center to arrange for a service evaluation. Listings of
Mitsubishi Authorized Service locations can be obtained from our
website site, www.mitsubishi-tv.com or by calling 1-800-332-2119.
15. PIP does not display a picture. • Make sure the V-Chip lock is off.
• Not all inputs can be displayed as a PIP.
16. Digital channels do not appear in PIP. Normal PIP operation.
17. Not all channels appear in multiple PIP/POP. Digital channels do not display in PIP/POP.
Problem Possible Solution
Troubleshooting
… 98 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD62527 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD62527 in the language / languages: English as an attachment in your email.

The manual is 9,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info