493633
16
Zoom out
Zoom in
Previous page
1/44
Next page
EN-16
Basic operation
Power-on
1. Turn on the device connected to the projector first.
2. Plug the power cord in the wall outlet.
The POWER indicator lights up.
If the power cord is unplugged from the wall outlet before the
projector is cooled down completely after use, the fans may
start rotating when the power cord is plugged in next time
and the POWER button may not function. In this case, wait
for the fans to stop and press the POWER button to light the
indicator.
3. Press the POWER button on the control panel or the ON button
on the remote control.
It may take about one minute for the lamp to light up.
The lamp occasionally fails to light up. Wait a few minutes
and try to light the lamp again.
After the POWER button is pressed, the image may flicker
before the lamp becomes stable. This is not a product mal-
function.
Regardless of the setting of LAMP MODE in the INSTALLA-
TION menu, the STANDARD lamp mode is activated by
default whenever the projector is turned on. The LAMP
MODE is set to either STANDARD or LOW depending on the
setting last selected, and you cannot switch the LAMP
MODE in about one minute after the lamp is on.
Important:
If the lamp exceptionally turned off due to the power interruption or
voltage drop, it can happen that the lamp does not turn on even if
you switch again the power supply on. In that case, please pull the
electric cord out of the consent and put it again in the consent
about 10 minutes later.
Do not cover the lens with the lens cap while the lamp is on.
The projector starts warming up when the POWER button is
pressed. During the warm-up process, images may appear dark
and no commands are accepted.
By blinking red, the STATUS indicator indicates that the lamp
should be replaced soon. Replace the lamp when the STATUS
indicator blinks red. (See page 37 and 40.)
Images may not be projected with good quality in an extremely hot
or cold environment. (This is not a product malfunction.)
In order to ensure the safety in case of trouble with the projector,
use an electrical outlet having an earth leakage breaker to supply
the power to the projector. If you do not have such outlet, ask your
dealer to install it.
4. Adjust the focus by turning the focus ring.
5. Choose your desired external input source using the COM-
PUTER, VIDEO or HDMI button.
The input source is switched between COMPUTER1,
COMPUTER2, and HDMI at every press of the COMPUTER
button on the control panel.
The input source is switched between VIDEO and S-VIDEO
at every press of the VIDEO button on the control panel.
When pressing COMPUTER (1 or 2), HDMI, VIDEO, or S-
VIDEO button on the remote control, the input source
switches directly as the button pressed.
The projector automatically selects the appropriate signal
format. The selected signal format is displayed on the
screen.
The COMPUTER, VIDEO and HDMI buttons don’t function
while the menu is being displayed.
When COMPUTER is chosen as the source, images sup-
plied from the computer may flicker. Press the W or X button
on the remote control to reduce flicker, if it occurs.
To avoid permanently imprinting a fixed image onto your pro-
jector, please do not display the same stationary images for
long period.
6. Adjust the image size by turning the zoom ring.
If necessary, adjust the focus and zoom again.
When fine streaks are seen on projected images
This is due to interference with the screen surface and is not a mal-
function. Replace the screen or displace the focus a little.
STANDBYON
ASPECTMAGNIFY
KEYSTONE
VO L PAG E
UP
DOWN
MENU
FREEZE
AU TO
POSITION
AV
MUTE
ENTER
1
2
COMPUTER
VIDEO
VIEWER
UNPLUG
S
-
VIDEO
WIRELESS HDMIDVI
4 FOCUS
6 ZOOM
53, 1, 2
5
1, 23
Indicator
Condition
STATUS POWER
Stand-by - Red
When the lamp is on. Green Green
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD620U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD620U in the language / languages: English as an attachment in your email.

The manual is 3,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info