32979

Mitsubishi WD52528 Manual

100
Zoom out
Zoom in
Previous page
1/110
Next page
100
Chapter 6. Special Features
30. The A/V Receiver is the selected audio source
but there is no sound.
• Check to see if the A/V Receiver power is turned on. After the power
is turned on, redisplay the Device Selection menu and press ENTER
to allow NetCommand to correctly select the A/V Receiver input.
• From the NetCommand menu, select Review. Check the Review
screen to see if the input for the A/V Receiver assigned to the
corresponds to the actual connections on the A/V Receiver. If
they do not match, either change the actual connections, or select
Change on the Edit NetCommand menu to change the device on the
Connection screen.
31. The TV Speaker icon or A/V Receiver icon is
grayed out and not selectable.
Select the Change setting from the Edit NetCommand menu, and then
select the device (for example VCR). Once the Connection screen is
displayed, check if the audio check box is selected for the TV input
and/or AVR input.
32. Cannot see the A/V Receiver menu. The A/V Receiver is not connected to any input of the TV. To check the
A/V Receiver menu, temporarily plug into an unused input of the TV,
such as Input 3 (on front). Then select Review from the NetCommand
Menu, turn the input On to view the A/V Receiver menu.
33. Screen is black when trying to view digital
channels or IEEE 1394 device.
The PerfectColor™ color balance has been incorrectly set. Reset the
color balance by repeatedly pressing the Video button on the remote
until the PerfectColor option appears. Press ENTER, then CANCEL
34. The REC button is not working, or, on the
Transport menu the record key is grayed out and
not available.
• The device does not support recording, such as a DVD player.
• Recordings can not be initiated from the Transport menu when using
an IEEE 1394 device. Select the source that will be recorded from the
Device Selection menu and press REC. The Record menu displays
allowing setup of a recording.
35. A program recorded from your TV is distorted
when played on a 4:3 TV.
TV was set to Anamorphic when program was recorded. Record
programs in Cropped mode if playing back on a 4:3 TV.
36. Excessive digital artifacts. • The IEEE 1394 cable is too long (15 feet between devices is the
maximum length).
• There may be a slow device in the middle of the IEEE 1394 network.
Move the slow devices to the end so that connections for faster
devices do not pass through them.
37. Cannot see a picture from a DV Camcorder. • Go to Device Selection menu and select analog connection.
• Connect the DV Camcorder to analog input (for example, Input-3).
Select NetCommand from the main menu, then Change. At the
Change screen, select the camcorder. On the Name screen, check
Analog Connection. Select the device and on the following screen,
select which analog input was used, and check audio and/or video.
38. DVCR analog/digital problems. If the tape is currently playing but no picture displays, there may be a
mismatch of the medium with the display. Press DEVICE to display the
Device Selection menu. Press ENTER for the DVCR device. If digital is
selected, try analog, or if analog is selected, try digital.
39. D-VHS recordings for digital cable have drop-
outs (loss of picture or sound), or no playback.
Digital cable signals on IEEE 1394 can exceed the data rate standards
supported by DVCR.
40. There is no audio and video from the IEEE 1394
device.
• The device is not turned on - turn the device power on.
• No medium (tape or disc) is inserted into the device.
• The medium is blank (has no recording).
• The play command failed - Try pressing play again on the device’s
remote control or front panel.
• The device is already in use (for example: the device is currently
recording).
• The source is copy-protected or violates copy protection.
• The device’s digital video signal is not supported by the TV, such
as DV video, common with camcorders. Use analog connections
instead, if available.
• The device is not an audio/video device.
• Too many other devices are already communicating over IEEE 1394.
Remove or stop some devices and try again.
Problem Possible Solution
Troubleshooting, continued
… 100 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD52528 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD52528 in the language / languages: English as an attachment in your email.

The manual is 9,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info