475255

Mitsubishi WD-82838 Manual

73
Zoom out
Zoom in
Previous page
1/110
Next page
6. NetCommand Control of an A/V Receiver (838 Series) 73
For assistance call 1(800) 332-2119
Before You Begin
To complete these steps you will need:
• The remote controls for both the TV and the
A/V receiver.
• An IR emitter cable available from Mitsubishi.
• An HDMI-to-HDMI cable to connect the A/V
receiver to the TV and cables necessary to
connect devices to the A/V receiver.
1.
Connect the A/V receiver to the TV with an HDMI-
to-HDMI cable. Do not connect the optional audio
cable at this time.
2.
If desired, enable HDMI Control of a CEC-enabled
A/V receiver. See Appendix C, “HDMI Control of
CEC Devices.”
3.
Connect your audio/video devices to the A/V
receiver. Note the name of the device connected
Pb Pr
INPUT 2
INPUT 1
DIGITAL
AUDIO
OUTPUT
(480i / 480p / 720p / 1080i)
Y/ VIDEO
Pb Pr
Y/ VIDEO
DVI/PC
LR INPUT
AUDIO
3D
GLASSES
EMITTER
ANT
AUDIO
LR
LAN
DIGITAL
AUDIO
OUTPUT
1
2
3
HDMI
HDMI cable
DIGITAL
AUDIO
OUTPUT
AUDIO
OUTPUT
LR
AUDIO
OUTPUT
LR
HDMI OUT
DIGITAL
AUDIO IN
ANALOG AUDIO IN
LR
High-definition
DVD player
DVD player
Cable box
VCR
Y/ VIDEO
TV
A/V receiver with
HDMI output
Any connection
types
Optional
analog or
digital audio
connection
Multiple video inputs through a single HDMI cable. The
optional audio connection allows you to hear, through the
A/V receiver, devices connected to the TV only, e.g., an
antenna on the
ANT
input.
to each A/V receiver input. This information will be
needed later to set up NetCommand’s automatic
input switching.
4.
If using an optional audio cable between the TV
and A/V receiver, connect it. Set up NetCommand
control of the A/V receiver’s TV audio input when
setting up automatic switching in the next procedure.
5.
Connect the IR emitter cable to the TV and position
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitters,” page 65.
Setup to Control Automatic Audio
and Video Switching via HDMI
When this setup is complete, the “learned” A/V receiver
input will appear in the TV’s Input Selection menu as a
selectable input.
1.
Set the TV’s remote control to TV mode.
2.
Navigate to the Inputs > AVR menu.
To set up A/V switching over HDMI, choose your A/V
receiver input from a list.
3.
In the Inputs > AVR menu, highlight the name of the
A/V receiver input to control. In this example, it is
the DVD input.
4.
Press
ENTER
on the TV’s remote control.
5.
While the text DVD is flashing, press and hold the
DVD INPUT
key on the A/V receiver’s remote control.
6.
When a check appears next to DVD, release the
DVD INPUT
key.
• If the text stops flashing before the check mark
appears, repeat this step.
• To erase the IR code just “learned,” press
CANCEL
while the name is highlighted.
7.
If using an optional audio cable between the TV and
A/V receiver, “learn” the
TV AUDIO OUT
key to enable
automatic switching of audio from sources con-
nected to the TV only.
8.
If there are no more devices to set up, highlight
EXIT and press
ENTER
or continue to set up addi-
tional A/V receiver audio/video sources.
Setting Up A/V Receiver Control, continued
… 73 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-82838 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-82838 in the language / languages: English as an attachment in your email.

The manual is 7,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info