475327

Mitsubishi WD-73C8 Manual

68
Zoom out
Zoom in
Previous page
1/94
Next page
68 Appendices
IMPORTANT
You may need to reprogram the remote
control after changing the batteries.
Programming the Remote Control
Move the slide switch at the top of the remote to
1.
the position for the product you want to control.
Refer to the table below. Only one of each device
type can be controlled in each slide-switch position.
Switch Position Affected Device
CABLE/SAT
Cable Box
DTV Receiver
Satellite Receiver
VCR
VCR
DVR
Laser Disc Player
DVD Player/Recorder
DVD
DVD Player/Recorder
DVR
Laser Disc Player
VCR
AUDIO
A/V Receiver
Audio Amplifier
CD Player
Press and hold
2.
POWER
on the remote control for
several seconds until the button blinks twice and
goes off.
Release the
3.
POWER
button.
Enter the first five-digit code listed for your equip-
4.
ment.
The •
POWER
button blinks twice when you start to
enter the code and then once for each addi-
tional keypress.
The •
POWER
button blinks twice when you finish
entering a valid code.
Move the slide switch to another position if you •
need to start over or wish to exit programming
mode.
Point the remote control at the equipment and
5.
press
POWER
. If the product has no power on/off
function, press a different key, such as (
PL AY
),
(
STOP
),
VOL
, or
MUTE.
If the equipment responds, the remote control •
is properly programmed to operate the equip-
ment.
If the equipment does not respond, repeat •
steps 2–4 with the next five-digit code listed for
your equipment.
Once you have found the correct code, write it in
6.
the space below for future reference.
Switch Position
Device Type Code
CABLE/SAT
VCR
DVD
AUDIO
Code Verification
To determine the code programmed for any position of
the slide switch:
Move the slide switch to the position you wish to
1.
verify.
Press and hold
2.
POWER
on the remote control for
several seconds until the button blinks twice and
goes off.
Press keys
3.
9 9 0
Press
4.
1
and count the blinks of the power button.
Write down the number of blinks as the first digit of
the code.
Repeat step 4 for the second, third, fourth, and fifth
5.
digits of the code.
Audio Lock: Universal A/V Receiver Control
With Audio Lock active, the remote control operates
the volume and mute functions of the A/V receiver in all
positions of the slide switch. Activate Audio Lock if you
normally use an A/V receiver with your TV and other
A/V equipment.
Program the
1.
AUDIO
position for your A/V receiver as
described earlier in this section.
With the slide switch in the
2.
AUDIO
position, press
and hold
POWER
on the remote control for several
seconds until the button blinks twice and goes off.
Press keys
3.
9 9 3 ENTER
The
POWER
button will blink twice to indicate Audio
Lock is active.
To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
Press and hold
1.
POWER
for several seconds until the
key blinks twice and goes off.
2. Press keys
2.
9 9 3 VOL
.
The
POWER
key will blink four times to indicate Audio
Lock has cleared.
Appendix C: Programming the Remote Control, continued
… 68 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-73C8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-73C8 in the language / languages: English as an attachment in your email.

The manual is 4,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info