475327
28
Zoom out
Zoom in
Previous page
1/94
Next page
28 4. TV Operation and Features
21.
MENU
: Displays the main TV menu. When a sub-
menu is open, backs up one menu level.
22.
EXIT:
Closes TV on-screen menus/displays.
23.
F1–F4
For devices under NetCommand control:
Perform NetCommand “Learning” to assign your
choice of functions to the
F1
F4
keys.
For devices operating independently of
NetCommand: The
F1
F4
keys work like the A,
B, C, D buttons on some cable boxes, satellite
receivers, and DVD players. Program the remote
control for your equipment and test the keys. See
Appendix C, “Programming the Remote Control.
25. (
PAUSE
): Freezes a broadcast TV picture from an
antenna source, cable box, or satellite receiver (if
key has not been reassigned for NetCommand use).
Record/Playback Keys
Use any of these methods to enable the recording and
playback commands of the TVs remote control:
• ProgramtheremotecontrolforyourDVR,VCR,or
DVD player/recorder and set the slide switch to
VCR
,
DVD
,
CABLE/SAT
, or
AUDIO
as appropriate.
• CheckHDMIdevicesforcompatibilitywiththeTV’s
NetCommand for HDMI feature (see Appendix E).
• 736 or 835 Series TV: Perform NetCommand IR
“learning” for the device.
24.
(
RECORD
):
Records with a VCR or DVR.
25. (
PAUSE
): Pauses a VCR, DVR, or DVD. See
above for use during TV viewing.
26.
(
STOP
): Stops play of a VCR, DVR, or DVD.
27.
(
REVERSE
): Rewinds a VCR. Reverse scans a
DVR or DVD.
28. (
PL AY
): Plays a VCR, DVR, or DVD.
29.
(
FORWARD
): Fast forwards a VCR. Forward scans
a DVR or DVD.
Remote Control, continued
Care of the Remote Control
Use only alkaline batteries.•
Be within 20 feet of the equipment.•
Do not press two or more buttons at the same time •
unless instructed to do so.
Do not allow unit to get wet or become heated.•
Avoid dropping on hard surfaces.•
Do not use harsh chemicals to clean. Use only a •
soft, lightly moistened cloth.
Do not mix old and new batteries.•
Resetting the Remote Control
If the slide switch is set to
TV
and the TV does not
respond properly, reset the remote control.
Press and hold
1.
POWER
for several seconds until the
button blinks twice and goes off.
Release the
2.
POWER
button.
Press keys
3.
0 0 9 3 5
and the
POWER
button will blink
twice when you finish entering the code. While
entering the code, pause for a moment between
each key press to ensure it is recognized.
Low-Battery Indicator
If you press a key and the
POWER
key blinks five times,
replace the remote control’s batteries.
Note: To operate other audio/video devices using
the TV’s remote control:
• SeeAppendixC,“ProgrammingtheRemote
Control.”
• ForHDMIdevicescompatiblewiththeTVsNet-
Command for HDMI feature, see Appendix E.
• 736 or 835 Series TV: See chapter 6, “NetCom-
mand IR Control,” for NetCommand IR “Learning”
of device keys.
• ForuseofspecifickeyswithNetCommand-con-
trolled devices, see “Special Operation Methods,
page 56.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-73C8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-73C8 in the language / languages: English as an attachment in your email.

The manual is 4,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info