475257

Mitsubishi WD-73838 Manual

78
Zoom out
Zoom in
Previous page
1/110
Next page
78 Appendices
For assistance call 1(800) 332-2119
Programming the Remote Control
1.
Press one of the upper buttons on the remote
control to change to the correct mode for the
product you want to control. Refer to the table
below. Only one of each device type can be con-
trolled in each mode.
Mode Affected Device
CAB/SAT
Cable Box
DTV Receiver
Satellite Receiver
VCR
VCR
DVR
DVD Player/Recorder
DVD
DVD Player/Recorder
DVR
VCR
AUDIO
A/V Receiver
Audio Amplifier
CD Player
2.
Press and hold
POWER
on the remote control for
several seconds until the key flashes twice and
goes off.
3.
Release the
POWER
key.
4.
Enter the first five-digit code listed for your equip-
ment in the reference tables that follow.
If you need to start over or wish to exit
programming mode, temporarily change to a
different device mode.
5.
Point the remote control at the equipment and
press
POWER
. If the product has no power on/off
function, press a different key, such as (
PLAY
),
(
STOP
),
VOLUME UP
, or
MUTE.
• If the equipment responds, the remote control
is properly programmed.
• If the equipment does not respond, repeat
steps 4 and 5 with the next five-digit code
listed for your equipment.
6.
Once you have found the correct code, write it in
the space below for future reference.
Mode
Device Type Code
CABLE/SAT
VCR
DVD
AUDIO
IMPORTANT
You may need to reprogram the remote control after
changing the batteries. Record the codes for each
mode in the space provided to make this faster.
Code Verification
To determine the code programmed for any mode:
1.
Set the mode to the one you wish to verify.
2.
Press and hold
POWER
on the remote control for
several seconds until the
key
flashes twice and goes
off.
3.
Press keys
9 9 0
4.
Press
1
and count the flashes of the power key.
Write down the number of flashes as the first digit
of the code.
5.
Repeat step 4 for the other digits of the code.
Press
2
to see flashes for the second digit, press
3
for the third digit,
4
for the fourth digit, and
5
for the
fifth digit.
Audio Lock: Universal A/V Receiver
Control
With Audio Lock enabled, the remote control oper-
ates volume and mute on an A/V receiver in all control
modes. Activate Audio Lock if you always use an A/V
receiver with your TV and other A/V equipment.
1.
Program
AUDIO
mode for your A/V receiver as
described in “Programming the Remote Control” on
this page.
2.
With the remote control in
AUDIO
mode, hold
POWER
on the remote control for several seconds until the
key flashes twice and goes off.
3.
Press keys
9 9 3 ENTER
The
POWER
key will flash twice to indicate Audio
Lock is active.
To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
1.
Press and hold
POWER
for several seconds until it
flashes twice and goes off.
2.
Press keys
9 9 3 VOLUME UP
.
The
POWER
key will flash four times to indicate Audio
Lock has cleared.
Appendix A: Programming the Remote Control, continued
… 78 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-73838 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-73838 in the language / languages: English as an attachment in your email.

The manual is 7,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info