475273

Mitsubishi WD-73837 Manual

79
Zoom out
Zoom in
Previous page
1/88
Next page
Appendices 79
Appendix E: Troubleshooting, continued
NetCommand IR Control (NetCommand-equipped models only)
Symptom Remarks
3. The A/V receiver is the selected audio source
but there is no sound.
A/V Receiver Set Up for Audio-Only Switching•
Check to see if the A/V Receiver power is turned on. -
With A/V receiver power turned on, redisplay the Activ- -
ity menu and press ENTER to allow NetCommand to
correctly select the A/V Receiver input.
Incorrect setup in the Inputs > AVR menu. Check the -
device connection assigned in the AVR menu.
A/V Receiver Set Up for Audio and Video Switching over HDMI•
Check to see if the A/V Receiver power is turned on. -
If the device is connected only to the TV (e.g., on ANT -
or a front panel input), verify that the TV’s AUDIO
OUTPUT is connected to the A/V receiver.
The A/V receiver is not switching properly because -
you have not learned the IR codes for the A/V receiver
inputs to which your devices are connected.
4. There is no sound from the A/V receiver
for my DVD player or other surround sound
device even though I learned the IR code for
the A/V receiver’s DVD input or other input.
(A/V Receiver Set Up for Audio-Only Switch-
ing)
NetCommand A/V receiver setup for the DVD player or digital
surround sound device or other device is not switching prop-
erly. See “Case 2: Automatic A/V Receiver Switching to a Sur-
round Sound Device,” page 54, and perform A/V receiver setup
for a digital surround sound device.
5. There is no sound or picture from the A/V
receiver for my DVD player or other device
connected to the A/V receiver; the A/V
receiver should be sending video to the TV
over an HDMI cable.
(
A/V Receiver Set Up for Audio and Video
Switching over HDMI)
The NetCommand A/V receiver setup is not switching audio
and video inputs properly because you did not “learn” the A/V
receiver’s IR codes for the device inputs. See “Case 3: Auto-
matic Audio and Video Switching via HDMI,” page 55.
6. I’ve selected my DVD player or other sur-
round sound device in combination with the
TV speakers but hear no sound from the TV
speakers.
A/V Receiver Set Up for Audio-Only Switching•
If you have only an audio connection from the device to the
A/V receiver, a physical audio connection from the device
to the TV is also required.
Connect the left and right audio output from the device -
to the appropriate TV audio input. Now you can hear
audio from the device through either the TV speakers or
the A/V receiver.
To switch audio sources, press MORE 9 (Audio), press -
to show the Speakers option, then press to
select AV Receiver or TV.
A/V Receiver Set Up for Audio and Video Switching over HDMI•
With your DVD player connected to the A/V receiver, only
video is passed from the A/V receiver to the TV because of
copy-protection restrictions on the HDMI signal
7. I “learned” the RECORD key for my VCR/DVR
but when I pressed the RECORD key, the
VCR/DVR did not record anything.
Check that the VCR or DVR is receiving a signal directly from
your cable box or satellite receiver.
… 79 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-73837 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-73837 in the language / languages: English as an attachment in your email.

The manual is 5,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info