475334

Mitsubishi WD-73835 Manual

54
Zoom out
Zoom in
Previous page
1/94
Next page
54 6. NetCommand IR Control (736 and 835 Series TVs)
To perform this procedure, you need:
The remote controls for both the TV and the •
device you want to control.
The IR emitter cable supplied with the TV.•
Note: To set up an A/V receiver, see “Set Up NetCom-
mand Control of an A/V Receiver” later in this
chapter.
Connect and position the IR emitters for the
1.
devices you wish to control. See “IR Emitter Place-
ment” on the previous page.
Set the
2.
TV’s remote control slide switch to the
TV
position and power on the TV if needed.
Open the NetCommand
3.
Learn screen in one of two
ways:
If working from the • Auto Input Sensing screen
for the device, highlight the Learn icon and
press
ENTER
to open the Learn screen for the
device.
If performing NetCommand setup at any time •
after the device has been recognized through
Auto Input Sensing:
a. Press
INPUT
to open the Input Selection
menu.
b. Highlight the desired input icon and press
ENTER
to switch to that input.
c. Press
MENU
, highlight Inputs, and highlight
Learn to open the Inputs > Learn screen
for the device.
The first function highlighted in the
4.
Learn screen
is always Power On. Aim the TV’s remote control
at the TV and press
ENTER
to begin learning for that
function.
When the
5.
Power On text starts flashing, aim the
device’s remote control at the TV and press and
hold the
POWER
key until a check mark appears next
to Power On.
If the text stops flashing before the check mark •
appears, repeat the previous step.
To remove the key from NetCommand control, •
press the
CANCEL
key while the key name is
highlighted.
Press the
6.
keys on the TV’s remote control
to highlight other keys on the list. Repeat steps
4 and 5 for each additional function you wish to
control through NetCommand.
If the device’s remote control has keys that are not
7.
in the list, you can associate up to any four keys
with the
F1
through
F4
keys. Perform NetCommand
setup for the
F
keys the same way you did for the
named keys
.
For example, you can:
Assign your DVD player’s •
CHAPTER SKIP FORWARD
and
CHAPTER SKIP BACK
keys to
F1
and
F2
.
“Learn” your A/V receiver’s DSP options for the •
current device.
If the device has a separate
8.
POWER OFF
key, press
on the TV’s remote to highlight Power Off.
Repeat the earlier steps to “learn” the
POWER OFF
key.
If the device has no
POWER OFF
key, skip this step.
Press
9.
EXIT
to finish NetCommand “learning” for the
current device.
From the Auto Input Sensing screen, highlight the Learn
icon and press ENTER to open the NetCommand Learn
screen.
Inputs > Learn screen
Adding or Removing Device Keys
from NetCommand Control
Press
1.
INPUT
to open the Input Selection menu, high-
light the device’s icon and press
ENTER
.
Open the
2.
Inputs menu and highlight the Learn icon.
When the
3.
Learn screen displays:
To add keys: Continue as described earlier •
under “Initial NetCommand Setup for Most
Devices” on this page.
To delete keys: Highlight the name of the key •
you wish to delete and press
CANCEL
on the TV‘s
remote control to clear the check mark.
Initial NetCommand Setup for Most Devices
… 54 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-73835 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-73835 in the language / languages: English as an attachment in your email.

The manual is 4,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info