Manual Mitsubishi WD-73734 (page 53 of 84) (English)

475299

Zoom out

Zoom in

1/84

6. NetCommand 53

Performthissetupto:

• OperatetheA/Vreceiver’spowerandvolume

functionswiththeTV’sremotecontrol.

• EnabletheA/Vreceivertoswitchautomatically

tothecorrectaudioinputwhenyouselecta

deviceintheTV’sInput Selectionmenu.

TosetupcontrolofanA/Vreceiveryouneed:

• TheremotecontrolsforboththeTVandthe

A/Vreceiver.

• TheIRemittercablesuppliedwiththeTV.

Note: Tosetupcontrolofotherdevicetypes,see

“InitialNetCommandSetupforMostDevices”

earlierinthischapter.

PerformthissetupusingtheInputs > AVRscreen,

shownbelow.

AVR screen overview

1. Powerandvolume

commands the TV can send to the

A/V receiver when “learned”

A check under

Learn/Name

means the TV has

“learned” the command to switch the A/V receiver to the

input.

Input1 through Input4 are placeholder names for A/V

receiver inputs. Use this screen to assign meaningful

names , e.g., the name of the A/V receiver input.

4. Match up devices connected to the TV inputs with

audio inputs on the A/V receiver.

3. SettheTV’sremotecontrolslideswitchtothe

position.

4. OpentheAVRscreeninoneoftwoways:

• IfusingtheAuto Output Sensingscreenfor

theA/Vreceiver,highlighttheLearniconand

press

ENTER

toopentheAVRscreen.

• IfperformingNetCommandsetupatanytime

aftertheA/Vreceiverhasbeenrecognized

throughAutoInputSensing:

Press

,highlightInputs,andhighlightAVR

toopentheAVRscreen.

5. ThefirstfunctionhighlightedintheAVRscreenis

alwaysPower On.AimtheTV’sremotecontrolat

theTVandpress

ENTER

tobeginlearningforPower

On.

A/V Receiver (AVR)

screen. Perform

NetCommand IR

“learning” for A/V

receiver power and

volume keys.

6. WhenthePower Ontextstartsflashing,aimthe

A/V receiver’sremotecontrolattheTVandpress

andholdthe

POWER

or

POWER ON

keyuntilacheckmark

appearsnexttoPower On.

• Ifthetextstopsflashingbeforethecheckmark

appears,repeatthisstep.

• ToremovethekeyfromNetCommandcontrol,

pressthe

CANCEL

keywhilethekeynameis

highlighted.

By completing “learning” for the power key,

NetCommand now operates the power function for

the A/V receiver.

Point the TV’s remote control at the TV to control

the A/V receiver.

7. Pressthe

keyontheTV’sremotecontroltohigh-

lightotherkeysinthelist.Repeatsteps5and6for

eachadditionalfunctionyouwishtocontrolthrough

NetCommand.

8. IftheA/Vreceiverhasaseparate

POWER OFF

key,

press ontheTV’sremotetohighlightPower Off.

Repeatsteps5and6to“learn”the

POWER OFF

key.

9. Whenfinished“learning”thepowerandvolume

keys,eitherpress

EXIT

towatchTVorproceedtothe

nextsectiontocontinueNetCommandsetupofthe

A/Vreceiver.

Setup to Control the A/V Receiver’s Power

and Volume Functions

1. ConnectyourA/VreceivertotheTVandanyaddi-

tionaldevices.Seechapter2,“TVConnections,”

forsuggestions.

2. ConnecttheIRemittercabletotheTVandposition

theIRemitterwhereitcansendsignalstotheA/V

receiver.

Set Up NetCommand Control of an A/V Receiver

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-73734 in the language / languages: English as an attachment in your email.

The manual is 3,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Mitsubishi WD-73734 Manual

Product: