475275

Mitsubishi WD-65C9 Manual

52
Zoom out
Zoom in
Previous page
1/88
Next page
52 6. NetCommand Control of an A/V Receiver (837 Series)
IMPORTANT
To hear audio sent from the TV to the A/V receiver,
you must have:
Physically connected the TV to the A/V receiver •
via the analog or digital audio output.
Assigned, if needed, the name AVR if using an •
HDMI A/V receiver.
“•
Learned” the IR codes for the A/V receiver
inputs.
Assigned the TV’s audio output to the correct •
input in the NetCommand Inputs > AVR menu.
Selected the A/V receiver as the audio source. •
Press MORE then 9 (AUDIO), then
to show
the Speakers option,
then
to select the A/V
Receiver.
Setting Up A/V Receiver Control
Power and Volume
Perform this setup to control the A/V receiver power
and volume with the TV’s remote control.
To perform this setup you need:
The remote controls for both the TV and the •
A/V receiver.
An IR emitter cable available from Mitsubishi.•
Before You Begin
Connect your A/V receiver to the TV and any addi-
1.
tional devices. See “Setting Up TV Inputs,” page 10
and “TV Connections,” page 14.
Connect the IR emitter cable to the TV and position
2.
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitter Placement,” page 46.
Set the
3.
TV’s remote control to
TV
mode using the
side button.
Setup to Control A/V Receiver Power and Volume
Open the
1.
Inputs > AVR screen in one of two ways:
If using the • New Device Found screen for the
A/V receiver, highlight NetCommand and press
ENTER
to open the AVR screen.
If performing NetCommand setup at any time •
after Auto Sensing:
Press
MENU
, highlight Inputs, and highlight AVR
to open the AVR menu.
The first function highlighted in the
2.
AVR screen is
always Power. Aim the TV’s remote control at the
TV and press
ENTER
to begin learning for Power.
Inputs > AVR screen. Perform
NetCommand IR “learning” for A/V
receiver power and volume keys.
When the
3.
Power text starts flashing, aim the A/V
receiver’s remote control at the TV and hold the
POWER
or
POWER ON
key until a check mark appears
next to Power.
If the text stops flashing before the check mark •
appears, repeat this step.
To remove the key from NetCommand control, •
press the
CANCEL
key while the key name is
highlighted.
Press the 4. key on the TV’s remote control to highlight
other keys in the list. Repeat steps 2 and 3 for each addi-
tional function you wish to control through NetCommand.
If the A/V receiver has a separate
5.
POWER OFF
key,
press on the TV’s remote to highlight Power Off.
Repeat steps 2 and 3 to “learn” the
POWER OFF
key.
If the device has no
POWER OFF
key, skip this step.
When finished “learning” the power and volume
6.
keys, either
To watch TV, press •
BACK
.
To continue with NetCommand setup to control •
switching of A/V receiver inputs, highlight
NEXT and press
ENTER
.
… 52 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-65C9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-65C9 in the language / languages: English as an attachment in your email.

The manual is 5,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info