475326

Mitsubishi WD-65C8 Manual

85
Zoom out
Zoom in
Previous page
1/94
Next page
Appendices 85
Appendix F: Troubleshooting, continued
Indicators
Symptom Remarks
1. LAMP indicator light is a constant red. Turn the TV off for at least 2 minutes. Turn it back on. If light is
still red, the lamp has failed. Replace it. See Appendix D for lamp
replacement information. For questions, please call Mitsubishi
Consumer relations at (800) 332-2119.
2. LAMP indicator light is a flashing yellow. Lamp cover door is open or lamp cartridge is not secure. See
Appendix D for lamp replacement information.
3. STATUS indicator light is a steady yellow. • Roomtemperaturehasexceededproperlevels.Coolthe
room.
• TheTVhasoverheated.Clearblockedairventsandensureat
least four inches of clearance on all sides of the TV.
• Cleantheairfilteronthelampcartridge.SeeAppendixD.
4. STATUS indicator light is a steady/flashing
red.
• UnplugsetfromACpower.Plugbackinandwaitoneminute
for blinking to stop.
• PressSYSTEMRESETbuttonandwaitforblinkingtostop.
• Ifblinkingcontinues,serviceisrequired.Contactyourdealer
or a Mitsubishi Authorized Service Center to arrange for a
service evaluation. Listings of Mitsubishi Authorized Service
locations can be obtained from our web site, www.mitsubi-
shi-tv.com or by calling 1-800-332-2119.
Sound (see also NetCommand troubleshooting for additional help with A/V receiver concerns)
Symptom Remarks
1. There is no sound even when the
volume is turned up.
• CheckiftheMUTEbuttonison.
• TheTV’s“Listento:”settingmaybesettoSAP.
• CheckthattheSpeakersoptionissettoTVtohearsoundfromthe
TV speakers.
• IfusinganA/Vreceiver,checkthattheSpeakersoptionissettoAV
Receiver to hear sound from the A/V receiver speakers.
• PerformaSystemReset.
2. The sound does not match the screen
picture.
The TV’s Listen to: setting may be set to SAP. See page 41.
3. The sound from my A/V receiver does
not match the screen picture (I should
hear the correct audio from my A/V
receiver).
Check that DIGITAL AUDIO OUTPUT and/or AVR AUDIO •
OUTPUT on TV’s back panel is connected to the A/V receiver.
Without this connection, devices connected only to the TV (and
not the A/V receiver) can be heard only from the TV speakers.
Note that this includes the ANT 1/ANT 2 inputs, a device (such
as a camcorder) connected to the front panel, and any other
device sending audio to the TV only.
Check A/V receiver input selection in the Inputs > AV Receiver •
menu.
If NetCommand is set up incorrectly for the A/V receiver,
see “A/V Receiver Control: Automatic Audio Switching,” page
59.
4. The sound from my A/V receiver does
not match the screen picture (my source
device should be sending both audio
and video through the A/V receiver).
Check A/V receiver input selection in the Inputs > AV Receiver •
menu.
If NetC
ommand is set up incorrectly for the A/V receiver,
see “Setup to Control Automatic Audio and Video Switching via
HDMI,” page 62.
The TV’s •
Listen to: setting may be set to SAP. See page 41.
5. Cannot select an audio-only device; it
does not appear in the Input Selection
Menu.
Plug a video plug into any composite
VIDEO
jack for the Auto Input
Sensing screen to appear. See “Audio-Only Device,” page 25.
… 85 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-65C8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-65C8 in the language / languages: English as an attachment in your email.

The manual is 4,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info